---
title: "P0107: intake pressure sensor (MAP): signal too low · cause and cost"
description: "Your intake pressure sensor (MAP) or barometric pressure sensor gives a signal that is too low, lower than is possible."
canonical: https://vroomdoctor.com/codes/p0107
language: en
---


# P0107: Intake pressure sensor (MAP): signal too low

Your intake pressure sensor (MAP) or barometric pressure sensor gives a signal that is too low, lower than is possible. Usually it is a loose connector or a faulty sensor.

Within a monthYou can keep driving, gently. Have it fixed within a month.

9:41Golf 1.4 TSI

1 fault found

P0107

Intake pressure sensor (MAP): signal too low

How badWithin a monthDrivingYes, calmlyAsk your Golf something…↑

**How bad:**

Within a month

**Do it yourself:**

Yes, you can do it yourself

**Garage:**

Depends on the cause

## What you notice

- The engine warning light is on

- Hard starting

- Hesitates when pulling away

- Car in limp mode

## What usually causes it

| Cause | Likelihood |
| --- | --- |
| Loose or corroded connector | Common |
| Faulty intake pressure sensor | Common |
| Broken supply or signal wire | Sometimes |
| Faulty engine computer (ECU) | Rare |

A code points to the area. Sometimes the garage only finds the real cause after that.

## How to fix it

Start with what costs least.

- 1Check that the connector on the sensor is firmly attached.

- 2Check the pins for corrosion.

- 3Have the 5 volt supply and the signal measured.

- 4If the wires are fine, fit a new sensor.

## What to ask the garage

- Which other codes are stored, and can I have the printout?

- Which measurement shows that this is the cause?

- What will it cost if you find more? Call me before you go ahead.

## If you wait

In the Saab 9-4X V6, the MAP sensor shares its 5 V supply with accelerator pedal sensor 2. A short circuit in one takes the other down with it. If there is also a code for the 5 V supply, start there.

First drive with the fault

The computer stores the fault.

Second drive in a row

The light comes on.

Code for the 5 V supply as well

Find the short circuit in that supply first. It affects more sensors.

At the APK

The APK inspector measures the exhaust gases. If they are too high, your car fails the APK.

## Background

How the air and fuel mixture is made

How it works ›

### How the intake pressure sensor is connected

The MAP sensor has three wires: a 5 V supply, earth and a signal wire. The voltage on the signal wire moves with the pressure in the intake manifold.

On a turbo diesel, the same type of sensor measures the boost pressure. The lowest pressure it can see there is the outside air pressure, at idle or with the engine off.

### When the computer sets the code

On the Saab 9-4X V6, the computer sets P0107 when the signal voltage stays below 0.20 V for more than 5 seconds. The test runs continuously while the engine is running.

The Saab 9-5 diesel sets the code when the signal wire is open or shorted for more than 1 second.

### In numbers

**Sensor supply:**

5 V from the engine computer1

**P0107 limit (Saab 9-4X V6):**

Below 0.20 V, for more than 5 s1

**Limit (Saab 9-5 diesel):**

Fault in the signal wire for more than 1 s2

**Shares 5 V supply with:**

Accelerator pedal sensor 2 (Saab 9-4X V6)3

**Engine warning light on:**

On the second drive in a row with the same fault4

**Engine warning light goes off:**

After 3 drives in a row without the fault5

## Questions

### What is the difference between P0107 and P0108?

With P0107 the signal is too low, with P0108 it is too high. The causes are similar.

### Can I replace the MAP sensor myself?

Usually, yes. It is often held on the intake manifold by one or two screws.

### Will P0107 make my car fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. You only fail if they are too high. The rules for each fuel type are in the APK guide. This fault can raise emissions.

## See also

- [P0106: Intake pressure sensor (MAP): range or performance problem](https://vroomdoctor.com/codes/p0106)

- [P0108: Intake pressure sensor (MAP): signal too high](https://vroomdoctor.com/codes/p0108)

- [Engine warning light](https://vroomdoctor.com/nl/waarschuwingslampjes/motorstoringslampje)

Was this helpful?

19 November 2026 · 6 sources · [In het Nederlands](https://vroomdoctor.com/nl/storingscodes/p0107)

## Sources

All sources checked on 19 November 2026.

- [Saab WIS, 9-4X 2011 V6: DTC P0107 or P0108 (factory manual)](https://saabwisonline.com/9-4x/2011/2-engine/engine-management-and-fuel-system-v6/fault-diagnosis-diagnostic-trouble-codes/dtc-p0107-or-p0108-lf1-lfw)

- [Saab WIS, 9-5 2011 diesel: DTC P0107 or P0108 (factory manual)](https://saabwisonline.com/9-5-9650/2011/2-engine/engine-management-and-fuel-system-4-cyl-diesel/fault-diagnosis-diagnostic-trouble-codes/dtc-p0107-or-p0108)

- [Saab WIS, 9-4X 2011 V6: DTC P0641, P0651, P0697 or P06A3 (factory manual)](https://saabwisonline.com/9-4x/2011/2-engine/engine-management-and-fuel-system-v6/fault-diagnosis-diagnostic-trouble-codes/dtc-p0641-p0651-p0697-or-p06a3-ecm-lfw)

- [Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)](https://saabwisonline.com/9-4x/2011/3-electrical-system/bus-and-diagnostics-communication/fault-diagnosis-fault-symptoms/powertrain-diagnostic-trouble-code-dtc-type-definitions)

- [UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8](https://www.transportpolicy.net/wp-content/uploads/2021/08/UNECE-R83.pdf)

- [RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)](https://www.rdw.nl/-/media/apk-handboek/pdf/apk-handboek-regelgeving-januari-2022.pdf)

## Your phone sees P0107 before you do.

Vroom Doctor is a small device that sits under your steering wheel. The app is free.

[Pre-order for €59](https://vroomdoctor.com/order)
