- How bad
- Within a month
- Do it yourself
- Possible, if you are handyYou always replace discs per axle, and always with new pads. Clean all the rust off the hub, or the new disc will shake too.
Prices
Including 21% VAT, 19 November 2026. Where do they come from? ›
Garage, with labour
Middle of 5, €109 to €450.
- MT Autoservice Almere19 Nov€109
- Vandaag Auto's19 Nov€125
- Auto Arts remblokken+remschijven per as19 Nov€280
- Univé artikel remschijven-vervangen-kosten19 Nov€450
- Vaartland tabel gemiddelde kosten19 Nov€450
ANWB: €300 to €600. Not counted.
Part only
Middle of 2, €42 to €49.
Without fitting. A garage often replaces more parts with it.
- mijnautoonderdelen categorie19 Nov€42
- autoonderdelen24 categorie19 Nov€49
What it does
The brake disc turns with the wheel. When you brake, the brake pads squeeze it. Heat and wear make a disc thinner or warp it.
How you notice
- Steering wheel or brake pedal shakes when you brake
- Deep grooves, or a lip on the outer edge
- Rust after standing still for a long time that doesn’t brake off
- Grinding noise
When to replace it
As a rule of thumb, with every second set of brake pads. The minimum thickness is on the disc.
If you wait
Below MIN TH
The disc is too thin. Replace it, together with the disc on the other side.
Only new pads
According to HELLA you only fit new pads if the disc is still above MIN TH.
After that
Deep grooves or cracks appear. According to Brembo the disc then has to be replaced.
At the APK
The inspector fails the car if the disc is so worn it could break. Or if rust covers more than half of the braking surface.
Background
How it works ›
What brake discs do
The brake disc is fixed to the wheel hub and turns with the wheel. When you brake, the brake pads squeeze the disc. That turns movement into heat.
Each time you brake, the disc wears a little too. That makes it thinner. A lip forms on the outer edge.
How you can tell they’re worn
On the edge or in the hat of the disc there’s a minimum thickness, with the letters MIN TH. If the garage measures less than that number, the disc has to come out.
Brembo measures in at least 4 places and takes the lowest value for the whole disc. As a rule of thumb you replace discs with every second set of brake pads.
If only one disc is too thin, you still replace both discs on that axle. The garage won’t fit new pads on a disc below MIN TH.
Why your steering wheel shakes when you brake
Shaking often comes from the disc wobbling. Brembo allows a maximum of 0.10 mm of runout, measured with the disc on the hub.
Rust or dirt between the hub and the disc is enough to cause runout. That’s why the mechanic cleans the contact surface before fitting a new disc. The hub itself may not have more than 0.050 mm of runout.
In numbers
- Minimum thickness
- Shown on the disc as MIN TH, in mm1
- Measuring
- In at least 4 places, the lowest value counts1
- Rule of thumb for replacing
- With every second set of brake pads1
- Replacement
- Always in pairs2
- Cracks or deep scratches
- Replace the disc5
- Maximum runout
- 0.10 mm3
- Maximum hub runout
- 0.050 mm3
- APK corrosion
- Clean braking surface on each side of at least 50% of the pad width4
Questions
Why does my steering wheel shake when I brake?
Usually because of unevenly worn or warped discs. Rust or dirt between the hub and the disc also makes the disc wobble. Brembo allows a maximum of 0.10 mm of runout.
Do brake discs fail the APK (the Dutch MOT)?
Yes, if the disc is so worn it could break. Or if rust covers more than half of the braking surface. Hairline cracks from heat aren’t a reason to fail.
Can you have brake discs skimmed?
Sometimes. If the disc stays above the minimum thickness (MIN TH) afterwards, it’s possible. If it’s below, it has to be replaced.
See also
Was this helpful?
· 5 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.