- How bad
- This week
- Do it yourself
- Possible, if you are handyWith a jack, axle stands and a torque wrench you can replace the front pads yourself. Always do both sides of an axle at the same time. If you have an electric handbrake, you need diagnostic equipment.
Prices
Including 21% VAT, 19 November 2026. Where do they come from? ›
Garage, with labour
Middle of 5, €109 to €350.
- Vandaag Auto's19 Nov€109
- Auto Arts Schiedam remblokken per as19 Nov€149
- Vaartland tabel gemiddelde kosten19 Nov€150
- Univé artikel remblokken-vervangen-kosten19 Nov€200
- Carpardoo magazine19 Nov€350
ANWB: average €200. Not counted.
Part only
Middle of 2, €28 to €45.
Without fitting. A garage often replaces more parts with it.
- mijnautoonderdelen categorie19 Nov€28
- autoonderdelen24 categorie19 Nov€45
What it does
Brake pads press against the brake disc when you brake. That friction slows the car down. The lining wears every time you brake. The front ones wear faster than the rear.
How you notice
- Squealing or grinding when you brake
- Brake light or wear indicator is on
- Longer stopping distance or a soft brake pedal
When to replace it
There’s no fixed interval. Replace them when there’s less than 2 mm of lining left or the wear indicator comes on.
If you wait
Past the wear limit, the steel plate touches the disc. Then the disc gets deep scratches. It then has to be replaced too.
At the APK the inspector measures the braking force on the roller tester. A car from 2012 on must decelerate at least 5.8 m/s² with the foot brake. Left and right may not differ by more than 30%.
Wear limit reached
There’s about 2 mm of lining left. The light comes on, or the metal strip starts squealing.
After that
The steel plate touches the disc. You hear grinding. The disc gets deep scratches.
At the garage
A disc with deep scratches has to be replaced too. Then you pay for pads and discs.
At the APK
You fail with too little braking force, or too big a difference between left and right.
Background
How it works ›
What brake pads do
Each brake pad has a layer of lining (the part that wears) on a steel plate. When you brake, the caliper presses the pads against the spinning brake disc. The friction slows the car.
Each time you brake, a little lining wears away. That’s why you always replace pads for the whole axle at once, so left and right brake equally hard.
How you can tell they’re worn
Brembo gives 2 mm of lining as the limit. If there’s less left, or the wear indicator comes on, all the pads on that axle need replacing.
A metal strip on the pad starts squealing when it touches the disc. On other pads an electrical contact turns on a light on your dashboard.
If your car has electrical contacts, they should be new at every pad change. HELLA prescribes that.
In numbers
- Wear limit
- 2 mm of lining1
- Wear indicator
- Usually at 2 mm2
- Replacement
- Always all the pads on an axle1
- Bedding in (Brembo)
- At least 200 km of gentle driving, no hard braking for longer than 3 seconds1
- Electrical wear contacts
- Replace them at every pad change2
- APK braking deceleration
- At least 5.8 m/s² (cars from 2012 on)3
- APK difference left and right
- Max. 30% per axle3
- Brake disc
- Replace when below the minimum thickness, shown as MIN TH on the disc4
Questions
What does replacing brake pads cost?
Usually €175 per axle. The cheapest garage charged €109, the most expensive €350. If the discs need doing too, garages charge another €109 to €450 per axle.
Do worn brake pads fail the APK (the Dutch MOT)?
Yes, if you brake too weakly or left and right differ too much. The inspector measures the braking force on the roller tester. A car from 2012 on must decelerate at least 5.8 m/s².
How thin can brake pads get?
Down to 2 mm of lining, according to Brembo. If there’s less left or the wear indicator comes on, replace all the pads on that axle.
See also
Was this helpful?
· 4 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.