Skip to contentBlack Friday · Reserve for €59 €69 after launch Reserve ›

Replacing the clutch: what does it cost?

€449

Usually, based on 3 Dutch garages. They charge €389 to €1,400.

You notice a slipping clutch when the revs go up but the car doesn’t go faster.

Within a monthYou can still drive. Plan it within a month.

How bad
Within a month
Do it yourself
No, that is a garage jobThe gearbox has to come out, so this is garage work.
Lasts
At least 6 years or 120,000 km

Prices

Including 21% VAT, 19 November 2026. Where do they come from? ›

Garage, with labour

€449

Middle of 3, €389 to €1,400.

ANWB: €300 to €1,000. Not counted.

Your garage charges something else? Tell us ›

Part only

€109

Middle of 2, €88 to €130.

Without fitting. A garage often replaces more parts with it.

What it does

The clutch connects your engine to the gearbox. When you press the pedal, they’re separated. Every time you pull away, it wears a little.

How you notice

  • Revs go up, car doesn’t go faster
  • It only bites right at the top
  • Burning smell after pulling away on a hill
  • Heavy gear changes, or rattling when you’re standing still

If you wait

  1. Start

    It bites higher than it used to.

  2. After that

    It slips when you accelerate, at first only now and then.

  3. At the end

    You can’t get going any more. The lining is worn down to the rivets.

Background

EngineClutchFlywheelClutch platePressure plateGearboxInput shaftOutput shaftDifferentialDriveshaftWheel
How power reaches the wheels
How it works ›

What the clutch does

The clutch connects the engine to the gearbox. A pressure plate clamps the clutch plate against the flywheel. When you press the pedal, the release bearing takes that clamping force away and you can change gear.

The clutch plate has friction lining on both sides. It wears every time the plate slips, especially when you pull away.

Why a clutch slips

The best-known cause is lining worn down to the rivets. According to ZF: lots of pulling away, a heavy foot or a sticky pedal.

Oil or grease on the lining also makes the clutch slip. That comes from a leaking oil seal on the engine or gearbox, or from a leak in the hydraulic operation.

The ANWB names city traffic and towing a heavy trailer as reasons for faster wear.

The dual mass flywheel

A dual mass flywheel is made of two masses with springs between them. It damps vibrations from the drivetrain.

Valeo advises checking the dual mass flywheel at every clutch change. A worn one can damage a new clutch.

LuK measures the play between the two masses. With a ball bearing it’s max. 1.6 mm, with a bush max. 2.9 mm.

In numbers

Lifespan
At least 6 years or 120,000 km1
How to spot it
Revs rise, speed doesn’t1
Cause of slipping
Worn lining, oil or grease on the lining, operation that doesn’t work properly2
Dual mass flywheel
Check at every clutch change3
DMF play with ball bearing
Max. 1.6 mm4
DMF play with bush
Max. 2.9 mm4

Questions

How long does a clutch last?

About 120,000 km, or at least 6 years according to the ANWB, the Dutch motoring club. Pulling away gently stretches that.

What is a dual mass flywheel?

A heavy wheel with springs inside that damps vibrations. Valeo advises checking it at every clutch change. That saves taking the gearbox out a second time.

Can I keep driving with a slipping clutch?

For a while. The longer you do, the more likely it gives up on the road.

See also

Car has no powerCar jerks when accelerating

Was this helpful?

· 4 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. ANWB: Clutch (Dutch)
  2. ZF Aftermarket (Sachs): clutch slipping
  3. PMM: Dual Mass Flywheels, inspection, diagnosis and replacement (Valeo)
  4. Schaeffler LuK Service Info 0560: common dual mass flywheel issues