Skip to content

P0106: Intake pressure sensor (MAP): range or performance problem

Your intake pressure sensor (MAP) or barometric pressure sensor gives a value that does not match how the engine is running. Usually it is a leaking hose or a dirty sensor.

Within a monthYou can keep driving. Have it checked within a month.

How bad
Within a month
Do it yourself
Yes, you can do it yourself
Garage
€389 to €1,400

What you notice

  • The engine warning light is on
  • Rough idle
  • Less power
  • Higher fuel consumption

What usually causes it

CauseLikelihood
Leaking or loose hose to the sensorCommon
Sensor dirty with oil or sootCommon
Faulty intake pressure sensorSometimes
Air leak in the intake manifoldSometimes
EGR valve does not close properly · €399Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Find the sensor on the intake manifold. Check the connector.
  2. 2If the sensor has a vacuum hose, check whether it is cracked.
  3. 3Remove the sensor. Clean it with contact cleaner.
  4. 4Ignition on, engine off. Compare the value with the outside air pressure.
  5. 5If the value is still off, fit a new sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

A MAP sensor that reads off also makes the calculated outside air pressure wrong.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Weeks of driving on

    The computer works with a wrong airflow.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, your car fails the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
EGR valveGarage €399Part €193

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

What the intake pressure sensor measures

The MAP sensor measures the pressure in the intake manifold. It gets 5 V from the engine computer and returns a voltage that moves with the pressure.

The computer uses the same sensor for the outside air pressure. With the ignition on and the engine off, it reads the MAP sensor as a barometer.

When the computer sets the code

P0106 is a logic check. The Saab 9-4X V6 uses models of the intake system to calculate what the mass airflow sensor, the MAP sensor and the throttle sensor should read. If a reading differs for more than 2 seconds, a code follows. Which sensor is out of step decides whether it becomes P0101, P0106 or P0121.

If you press the accelerator fully from standstill, the MAP value should rise quickly to almost the outside air pressure, according to the manual.

In numbers

Sensor supply
5 V from the engine computer2
Code set after
More than 2 s of difference from the calculated airflow1
Test runs at coolant temperature
69 to 127 °C1
Test runs at engine speed
400 to 7,000 rpm1
Engine warning light on
On the second drive in a row with the same fault3
Engine warning light goes off
After 3 drives in a row without the fault4

Questions

What does a MAP sensor do?

It measures the pressure in the intake manifold. The engine computer uses it to calculate how much air the engine gets.

What does a new MAP sensor cost?

The part varies by engine. At a garage there is usually half an hour of labour on top, at €75 to €103 per hour.

Will P0106 make my car fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. You only fail if they are too high. The rules for each fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0106 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: DTC P0107 or P0108 (factory manual)
  3. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  4. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  5. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.