Skip to content

P0108: Intake pressure sensor (MAP): signal too high

Your intake pressure sensor (MAP) or barometric pressure sensor gives a signal that is too high, higher than is possible. Usually it is a faulty sensor or a short circuit in the wires.

Within a monthYou can still drive, gently. Plan the repair within a month.

How bad
Within a month
Do it yourself
Yes, you can do it yourself
Garage
€329 to €600

What you notice

  • The engine warning light is on
  • Black smoke, or it runs rich
  • Higher fuel consumption
  • Rough idle

What usually causes it

CauseLikelihood
Faulty intake pressure sensorCommon
Loose or leaking hose to the sensorSometimes
Short circuit to positive in the wiresSometimes
Poor earth connectionRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check the connector and the vacuum hose of the sensor.
  2. 2Check the wires for damage.
  3. 3Have the signal measured, with the ignition on and at idle.
  4. 4If the signal stays too high, fit a new sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

On the Saab 9-4X V6, the MAP sensor and accelerator pedal sensor 2 share the same 5 V supply. A short circuit affects both. If you also see a code for that supply, look there first.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Code for the 5 V supply as well

    Find the short circuit in that supply first. It affects more sensors.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, your car fails the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Catalytic converterGarage €339Part €240

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

How the intake pressure sensor is connected

The MAP sensor has a supply wire with 5 V, an earth wire and a signal wire. The voltage on that signal wire goes up and down with the pressure in the intake manifold.

On a turbo diesel, the same type of sensor measures the boost pressure. The lowest pressure it can see there is the outside air pressure, at idle or with the engine off.

When the computer sets the code

On the Saab 9-4X V6, the computer sets P0108 when the signal voltage stays above 4.80 V for more than 5 seconds. The test runs continuously while the engine is running.

The Saab 9-5 diesel sets the code when the signal wire is open or shorted for more than 1 second.

In numbers

Sensor supply
5 V from the engine computer1
P0108 limit (Saab 9-4X V6)
Above 4.80 V, for more than 5 s1
Limit (Saab 9-5 diesel)
Fault in the signal wire for more than 1 s2
Shares 5 V supply with
Accelerator pedal sensor 2 (Saab 9-4X V6)3
Engine warning light on
On the second drive in a row with the same fault4
Engine warning light goes off
After 3 drives in a row without the fault5

Questions

Can P0108 damage the engine?

Not directly. A rich mixture does strain the catalytic converter over time. On diesels, the diesel particulate filter (DPF) too.

What does it cost to fix P0108?

Usually a new sensor plus labour. Both vary by engine. Garages charge €75 to €103 per hour.

Will P0108 make my car fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. You only fail if they are too high. The rules for each fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0107 or P0108 (factory manual)
  2. Saab WIS, 9-5 2011 diesel: DTC P0107 or P0108 (factory manual)
  3. Saab WIS, 9-4X 2011 V6: DTC P0641, P0651, P0697 or P06A3 (factory manual)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  6. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.