Skip to content

P0327: Knock sensor 1 signal too low (bank 1)

Knock sensor 1 gives a signal that is too weak, on bank 1 or if your engine only has one. Usually the sensor is loose, or it is faulty.

Within a monthYou can keep driving. Have it fixed within a month, before you make long drives under heavy load.

How bad
Within a month
Do it yourself
Possible, if you are handy
Garage
Depends on the cause

What you notice

  • Slightly less power
  • You use more fuel
  • Slower acceleration
  • Often you notice nothing else

What usually causes it

CauseLikelihood
Sensor is loose, or tightened too muchCommon
Faulty knock sensorCommon
Short to earth, or a break in the cableSometimes
Corroded connectorSometimes
Fault in the engine computerRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Does the connector on the knock sensor click firmly into place? Also look for corrosion.
  2. 2Is the sensor firmly tightened? A loose sensor gives a signal that is too weak.
  3. 3Have the cable tested for a short to earth and for a break.
  4. 4Have the sensor replaced and tightened to the correct torque.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

With a circuit fault, the Saab retards the ignition. This keeps the engine from being damaged. According to HELLA, this costs some power and fuel.

When fitting, pay attention to the sensor itself. The manual lists a dropped or damaged sensor, a bolt tightened too loosely or too tightly, and dirt on the mounting surface. Thread-locking compound does not belong on the thread.

  1. Code appears

    The computer retards the ignition.

  2. Weeks of driving on

    The engine pulls slightly less. It uses more fuel.

  3. At the APK (the Dutch MOT)

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

Background

+−BatteryEngine managementIgnition coilSpark plugCylinder headSparkPiston
How the ignition works
How it works ›

What the knock sensor does

The knock sensor is a piezo element on the engine block. It turns engine vibrations into an alternating voltage. The engine computer learns what noise level is normal. On top of that, it recognises the pinking of an early combustion.

If the computer hears pinking, it retards the ignition. After that it keeps trying to return to the normal timing.

When the computer sets the code

P0327 means a signal that is too low. The Saab 9-4X V6 sets the code if the signal wires of the sensor on bank 1 are shorted to earth for more than 10 seconds.

The 2.8 turbo looks at the level. If, above 1,960 rpm, the signal stays below the noise level the engine always makes for more than 1 second, P0327 follows.

In numbers

Signal
Alternating voltage from a piezo element3
P0327 limit (Saab 9-4X V6)
Short to earth, for more than 10 s1
P0327 limit (Saab 9-4X 2.8 turbo)
Below the minimum noise level, for more than 1 s2
Computer response
Ignition retarded1
Voltage at unplugged connector (Saab 9-4X 2.8 turbo)
2.30 to 2.80 V to earth2
Engine warning light on (Saab 9-4X 2.8 turbo)
On the second drive in a row with the same fault5

Questions

What is the difference between P0325 and P0327?

P0325 is a general fault in the circuit. With P0327 the signal is too low, often because of a loose sensor or a short to earth.

Can I keep driving with P0327?

Yes, usually. The engine retards the ignition. It then runs with a little less power and economy.

Can a loose knock sensor cause P0327?

Yes. The sensor must sit firmly on the block to pick up vibrations. If it is loose, the signal becomes too weak.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0324 to P0333, P06B6 or P06B7 (factory manual)
  2. Saab WIS, 9-4X 2011 2.8 turbo: DTC P0326 to P0333 (factory manual)
  3. Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
  4. HELLA Tech World, Check knock sensor: function, fault symptoms and testing
  5. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  6. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)