- How bad
- Within a month
- Do it yourself
- Possible, if you are handy
- Garage
- Depends on the cause
What you notice
- Slightly less power
- You use more fuel
- Sometimes pinking or ticking when pulling away
- Often you notice nothing else
What usually causes it
| Cause | Likelihood |
|---|---|
| Loose or corroded connector | Common |
| Faulty knock sensor | Common |
| Damaged cable, from heat or rodents | Sometimes |
| Sensor is loose, or tightened too much | Sometimes |
| Fault in the engine computer | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Find the knock sensor on the engine block. Is the connector firmly in place, and is it clean?
- 2Follow the cable. Look for melted spots, breaks or rodent damage.
- 3Have the resistance and signal of the sensor measured.
- 4Is the sensor tightened to the specified torque? Too loose or too tight gives a wrong signal.
- 5Replace the knock sensor. If it sits under the intake manifold, it is a job for the garage.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What will it cost if you find more? Call me before you go ahead.
If you wait
With a fault in the circuit, the Saab retards the ignition. This protects the engine. HELLA lists less power and higher fuel use as the result.
When fitting, look at the sensor itself. The manual lists a dropped or damaged sensor, a bolt that is too loose or too tight, and dirt on the mounting surface. No thread-locking compound belongs on the thread.
Code appears
The computer retards the ignition.
Weeks of driving on
You have a little less power. You use more fuel.
At the APK (the Dutch MOT)
The APK inspector measures the exhaust gases. If they are too high, you fail the APK.
Background
How it works ›
What the knock sensor does
The knock sensor is a piezo element on the engine block. It turns engine vibrations into an alternating voltage. The engine computer learns what noise level is normal. On top of that, it recognises the pinking of an early combustion.
If the computer hears pinking, it retards the ignition. After that it keeps trying to return to the normal timing.
When the computer sets the code
P0325 means an open circuit. The Saab 9-4X V6 sets the code if the two signal wires of the sensor on bank 1 have no connection for more than 10 seconds.
On that car, a short to earth is P0327 and a short to positive is P0328.
In numbers
Questions
What does a knock sensor do?
It hears pinking, an early ignition in the cylinder. The computer then retards the ignition. That prevents damage to the pistons.
Can I keep driving with P0325?
Yes, usually. The engine protects itself by retarding the ignition. You mainly notice a little less power and higher fuel use.
Does filling up with 98 help with P0325?
No. The code points to a fault in the sensor or the wiring. It has nothing to do with the fuel.
Can I replace the knock sensor myself?
If it is easy to reach, yes, with a torque wrench. On many V engines it sits under the intake manifold. Then it is work for the garage.
See also
Was this helpful?
· 6 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-4X 2011 V6: DTC P0324 to P0333, P06B6 or P06B7 (factory manual)
- Saab WIS, 9-4X 2011 2.8 turbo: DTC P0326 to P0333 (factory manual)
- Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
- HELLA Tech World, Check knock sensor: function, fault symptoms and testing
- Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
- RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)