- How bad
- Within a month
- Do it yourself
- Possible, if you are handy
- Garage
- Depends on the cause
What you notice
- The glow plug light flashes or stays on
- Poor starting in the cold
- White smoke and rough running just after starting
What usually causes it
| Cause | Likelihood |
|---|---|
| Faulty glow plug relay or glow plug module | Common |
| Damaged module connector or wiring | Sometimes |
| Blown fuse in the glow plug circuit | Sometimes |
| Short circuit in a glow plug | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Check the fuse for the glow plug preheat circuit.
- 2Check that the connector on the glow plug module is firmly attached and dry.
- 3Have the glow plugs measured. One faulty plug can make the module switch off.
- 4Replace the glow plug module or the relay.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What will it cost if you find more? Call me before you go ahead.
If you wait
On Saab these are type C codes. The engine warning light stays off. The code is only stored in the memory.
Without glow plug preheat, the diesel starts worse when it is cold. The post-glow after starting also stops. That causes white smoke and a rough idle.
Code appears
The computer stores the fault.
Cold weather
The diesel starts worse. After starting it can give off white smoke.
At the APK
If a diesel particulate filter (DPF) is registered on the number plate, the APK (the Dutch MOT) inspector does not read the OBD. He measures with a particle counter.
What it costs
It depends on the cause. Where do the prices come from? ›
| Part | At the garage | Part only |
|---|---|---|
| Glow plugs | Garage none | Part €13 |
Background
How it works ›
How glow plug preheat works
A diesel ignites its fuel with the heat of compressed air. In a cold engine, that heat leaks away into the block. Glow plugs heat the combustion chamber before and during starting.
In the Saab 9-5 diesel, a separate module controls the glow plugs, each one individually. The engine computer drives that module with a pulsed signal and gets feedback.
What the code means
P0670 is about the glow plug module and its control circuit. The glow plugs themselves have their own codes. Saab reports a fault on the control wire lasting longer than half a second as P0380, P0383 or P0384.
Saab reports an internal fault in the module per cylinder, as P0671 to P0674. The tests run once per drive, at 9 to 16 V.
In numbers
Questions
Can I drive with P0670?
Yes. A warm engine does not need glow plug preheat. In frost, though, the car can start poorly or not at all.
What is the difference from a faulty glow plug?
With P0670, the control does not work. With a faulty glow plug, you usually get a code per cylinder, such as P0671.
What does a glow plug module cost?
The part and labour time differ per engine. Garages charge €75 to €103 per hour.
See also
Was this helpful?
· 5 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-5 2011 diesel: Glow Plug System Description (factory manual)
- Saab WIS, 9-5 2011 diesel: DTC P0380, P0383 or P0384 (factory manual)
- Saab WIS, 9-5 2011 diesel: DTC P0671 to P0674 (factory manual)
- Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
- RDW, APK Keurmeester no. 110 (September 2025): when is a soot measurement required? (in Dutch)
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.