Skip to contentBlack Friday · Reserve for €59 €69 after launch Reserve ›

Resetting the engine light: how to do it and when not to

Fix the cause first, then clear the code with an OBD scanner. Once the cause is gone, on most cars the light also goes off by itself after a few drives.

Why reset

After a repair you want to see whether the problem is gone. If you clear the code, you see straight away whether it comes back.

Sometimes the cause is already gone, like a fuel cap that wasn’t closed properly. Then resetting saves you a few days with a light on.

Always write down the code before you reset. Otherwise you lose the information the garage needs.

A reset only removes the warning. The part stays as it was.

Resetting with a scanner

Plug the scanner into the OBD port under the dashboard. Switch the ignition on. The engine can stay off.

Read the fault codes first and write them down. Also save the freeze frame if your scanner shows it.

Choose clear fault codes. The light goes off. Start the engine and check the light stays off.

Then do a few drives, including a stretch outside town. If the light comes back, the problem is still there.

Off by itself

Often, yes. If the engine computer no longer sees the fault, it turns the light off. The European OBD rules allow that after three consecutive drive cycles without the fault.

The fault code then stays in the memory for a while as a history code. So a garage can see that something was wrong.

If the light doesn’t go off, the fault is still there or the car isn’t running the test. Some tests only run on a cold start or on the motorway.

Disconnecting the battery

On older cars that sometimes works. Still, it’s not a good idea. You wipe everything at once, including information you’ll need later.

On modern cars you can lose settings. Think of the radio code, windows that need to relearn, or the learned values of the engine and gearbox. The car can run unevenly for a while afterwards.

When you’d better not reset

If the light flashes, the engine is misfiring. Resetting doesn’t fix that. Driving on can damage the catalytic converter. Have the car checked.

Don’t reset the light just before the APK (the Dutch MOT). After a reset the car runs its self-tests again. Until they’re done, the inspector measures the emissions with an exhaust gas test.

If you’re selling the car, don’t reset to hide the problem. A buyer with a scanner can tell from the unfinished self-tests that codes were cleared recently.

When you’d better not reset
SituationReset?Why
Fuel cap was loose and has been tightenedYesThe cause is gone, you see straight away whether that’s right
Part replaced after a fault codeYesYou test whether the repair works
Light flashesNoThe engine is misfiring and the catalytic converter is at risk
A week before the APKNoThe self-tests won’t be finished
Cause unknownNoFirst write down the code and look for the cause

Other lights

On many cars you reset the service light through the dashboard menu or with a button combination. It’s in the owner’s manual. Only do it once the service has been done.

The tyre pressure light often goes off after pumping up the tyres and a short drive. On some cars you first save the new pressure in the menu.

You can’t clear airbag and ABS lights with a normal engine scanner. For that you need a more expensive scanner or the garage.

Background

Vroom Doctor in the OBD port under the steering wheel, above the pedals
How it works ›

In numbers

Light goes off by itself
after 3 consecutive drive cycles without the fault1
Reading codes and resetting at the garage (ANWB)
€25 to €60 for reading, resetting sometimes extra2
APK shortly after clearing
self-tests not finished, then an exhaust gas test follows3
Flashing engine light
stop in a safe place4

Questions

How long before the engine light goes off by itself?

After three consecutive drive cycles without the fault, according to the European rules. How long that takes depends on which test the car has to run again.

Will the light come back if I reset it?

Yes, if the cause is still there. Sometimes within a minute, sometimes after a few days.

Can the garage see that I reset the light?

Often, yes. The self-tests then show as not ready. Some cars also keep history codes.

What does it cost to have the engine light reset?

Reading codes at a garage costs €25 to €60, according to the ANWB (the Dutch motoring club). Clearing is usually done at the same time. With your own scanner it costs nothing extra.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

  1. EUR-Lex: Directive 98/69/EC, Annex XI on OBD systems (Dutch)
  2. ANWB: having your car’s codes read (Dutch)
  3. RDW APK manual: noise and environment (Dutch)
  4. ANWB: warning lights, stop or drive on (Dutch)
  5. Kia Sportage owner’s manual: warning and indicator lights (Dutch)