Skip to contentBlack Friday · Reserve for €59 €69 after launch Reserve ›

Reading your fault code yourself

Plug a scanner into the port under your steering wheel, switch the ignition on and read the codes. A code points to the area, not always the part.

What you need

You need an OBD scanner. That’s a little box with a screen, or a small plug that talks to your phone.

Cheap plugs (ELM327) read the engine. For ABS and airbag you need a more expensive one.

Vroom Doctor is one of those plugs, with a free app that explains the code. It reads the engine, not ABS or airbag.

Some plugs only work with Android.

Step by step

  1. 1Find the port: under the dashboard, to the left of the steering wheel.
  2. 2Engine off, scanner in, ignition on.
  3. 3Read the codes. Take a screenshot, including of ‘pending’ codes.
  4. 4Also look at the freeze frame: engine speed, temperature and speed when it went wrong.

What the letters mean

Every code has 5 characters. The first letter tells you which part of the car the fault is in. The second character tells you whether it’s a generic code or a manufacturer code.

The last 3 digits point to the problem itself. P0300: random cylinder misfire. P0301: cylinder 1 misfire.

What the letters mean
CharacterMeaningExample
PPowertrain: engine, exhaust and gearboxP0420, catalytic converter
CChassis: ABS, brakes and suspensionC0035, wheel speed sensor
BBody: airbag, lighting and comfortB0001, driver airbag
UNetwork: communication between computersU0100, no contact with the engine computer
0 as second characterGeneric code, the same for every makeP0171, mixture too lean
1 as second characterManufacturer codeP1xxx, meaning differs per make

After reading

Look up the code. Look at the meaning and at the most common causes. A code points to a system and rarely to one part.

P0171, for example, means the mixture is too lean. That can be an air leak, a dirty mass air flow sensor or a weak fuel pump. Start with the cheapest and most likely cause.

If there are several codes, look at which came first. Low battery voltage, for example, can cause a whole string of other codes.

Also check whether the code is confirmed or pending. A pending code is one the car has seen once. A confirmed code has happened more often and usually turns on the engine light.

Clearing

You can, but only once you’ve written the code down and fixed the cause. A cleared code comes back if the problem is still there.

After clearing, the car runs its self-tests again. Until they’re done, the scanner reports that the monitors aren’t ready. So don’t clear codes just before the APK (the Dutch MOT).

When to go to the garage anyway

If the engine light flashes or a red light is on, have the car checked soon. The same goes for codes to do with brakes, airbag or steering.

If the cheap steps don’t sort it, the garage has better equipment. It can run tests per make and control parts. Take your code and the freeze frame with you.

Background

Vroom Doctor in the OBD port under the steering wheel, above the pedals
How it works ›

In numbers

P0 codes
standard codes, the same for every make2
P1 codes
manufacturer codes2
Engine light goes off by itself
after 3 consecutive drive cycles without the fault3
Reading codes at the garage (ANWB)
€25 to €601
APK after clearing
self-tests not finished, then an exhaust gas test follows4

Questions

Can I read a fault code with my phone?

Yes, with a small plug in the port and an app. Without the plug your phone can’t do it.

Does every scanner read all fault codes?

No. Cheap scanners usually only read the engine computer. For ABS, airbag and gearbox you often need a more expensive scanner.

Does the engine light go off if I clear the code?

Yes, until the fault comes back. Only clear it once the problem is gone.

See also

Was this helpful?

· 4 sources · In het Nederlands

Sources

  1. ANWB: having your car’s codes read (Dutch)
  2. EUR-Lex: Directive 1999/102/EC, OBD requirements (diagnostic connector and fault codes) (Dutch)
  3. EUR-Lex: Directive 98/69/EC, Annex XI on OBD systems (Dutch)
  4. RDW APK manual: noise and environment (Dutch)