Skip to content

P0016: Crankshaft and camshaft out of sync

Your crankshaft and your intake camshaft are no longer in sync, on bank 1. Usually a stretched timing chain or a belt that has jumped a tooth.

This weekDrive as little as possible. Have the timing checked this week.

How bad
This week
Do it yourself
No, that is a garage job
Usually
Stretched chain or worn chain tensioner
Garage
usually €712

What you notice

  • The engine warning light is on
  • Rattling on a cold start
  • Hard starting or stalling
  • Less power

What usually causes it

CauseLikelihood
Stretched chain or worn chain tensioner · €712Common
Timing belt that has jumped a tooth or is worn · €725Sometimes
Faulty actuator or solenoid valveSometimes
Faulty camshaft or crankshaft position sensor · €89Sometimes
Damaged reluctor ring on the crankshaft or camshaftRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Read all codes. Also note any codes for the sensors or the valve timing adjustment.
  2. 2Check the oil and the oil level.
  3. 3Listen on a cold start. Rattling in the first few seconds points to the chain.
  4. 4Have the garage read out the deviation and measure the timing.
  5. 5Chain stretched or belt jumped? Then fit a new timing kit.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

A chain that stretches further gets louder. The camshaft position shifts further. According to the ANWB, a broken timing drive can cause engine damage that cannot be repaired.

  1. First drive with the fault

    The computer stores the fault. The light stays off for now.

  2. Second drive in a row

    The light comes on.

  3. Driving on with a stretched chain

    The stretch increases. The rattling gets louder.

  4. Timing drive breaks

    Risk of engine damage that cannot be repaired.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Timing chainGarage €712Part €100
Timing beltGarage €725Part €49
Camshaft position sensorGarage €89Part €24
Crankshaft position sensorGarage €89Part €27

Background

CamshaftsCrankshaftTensionerWater pumpTiming beltTiming marks keep crankshaft and camshaft in step
How the crankshaft and camshaft run together
How it works ›

What the engine computer compares

The crankshaft position sensor and the camshaft position sensor both send out pulses. The engine computer compares those pulses and so knows whether the camshaft is in the right position relative to the crankshaft. With P0016, that relationship is wrong on bank 1, with the intake camshaft as the reference.

In the factory manual for the Saab 9-4X V6, the computer sets the code when the intake camshaft on bank 1 is more than 9 degrees too late or 12 degrees too early. The test runs with the actuator in its rest position, so only the mechanical position counts.

Chain, belt or sensor

A wrong position comes from the timing drive itself or from an incorrectly fitted chain. If P0016 to P0019 are all present at once, the manual points to the main chain or to a shifted reluctor wheel on the crankshaft.

According to the ANWB (the Dutch motoring club), you hear a bad chain as rattling or ticking straight after a cold start, louder at higher revs. A chain can be stretched too far at around 200,000 km or more.

In numbers

Limit intake camshaft bank 1 (Saab 9-4X V6)
More than 9 degrees too late or 12 degrees too early1
Test runs
With the camshaft actuator in its rest position1
All four codes P0016 to P0019
Points to the main chain or a shifted crankshaft sensor wheel1
Engine warning light on
On the second drive in a row with the same fault2
Audible sign of a bad chain
Rattling straight after a cold start, louder at higher revs3
Chain stretched too far
Can happen at around 200,000 km or more3

Questions

Is P0016 always the timing chain?

No. A sensor or the adjustment can also cause it. Always have the timing checked, though.

Which engines often get P0016?

On the VW 1.2 TSI and 1.4 TSI, a stretched chain is a known problem. It also happens on other chain-driven engines.

What does a new timing chain cost?

Garages charge €479 to €1,000, depending on the engine.

Will P0016 fail the APK (the Dutch MOT)?

For most cars, not on the light alone. Have it repaired first anyway. The risk of engine damage is high.

See also

Was this helpful?

· 3 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0016 to P0019 (factory manual)
  2. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  3. ANWB, Which is better: timing belt or chain? (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.