Skip to content

P0340: Camshaft position sensor A circuit fault (bank 1)

The engine computer is not getting a good signal from camshaft position sensor A, on bank 1 or if you only have one. Usually it is the sensor or the connector.

This weekYou can drive calmly to the garage, this week. Avoid unnecessary stops on the way. After you switch off, it sometimes will not start again.

How bad
This week
Do it yourself
Possible, if you are handy
Usually
Faulty camshaft position sensor
Garage
usually €89

What you notice

  • Long cranking before it starts
  • Limp mode
  • Hesitation or misfire
  • Sometimes stalls
  • You use more fuel

What usually causes it

CauseLikelihood
Faulty camshaft position sensor · €89Common
Loose, greasy or corroded connectorCommon
Damaged cable to the sensorSometimes
Weak battery, voltage drops too far when starting · €118Sometimes
Timing belt that has jumped a tooth, or a damaged sensor wheel · €725Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check the battery voltage in the app while starting. If it drops below about 9.5 volts, charge or replace the battery first.
  2. 2Does the camshaft position sensor connector click firmly into place? Also look for oil and corrosion.
  3. 3Follow the cable to the sensor. Look for chafed or melted spots.
  4. 4Have the sensor signal measured. If it drops out, fit a new sensor.
  5. 5If the code comes back with a new sensor, have the timing checked.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

With an active code, the engine takes longer to start. The Saab puts the variable valve timing (VVT) in its rest position.

HELLA lists damage, a broken sensor wheel and an internal short circuit as causes.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The engine warning light comes on. The engine sometimes takes longer to start.

  3. Signal drops out while driving

    The engine can stall.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Camshaft position sensorGarage €89Part €24
BatteryGarage €118Part none
Timing beltGarage €725Part €49

Background

CamshaftsCrankshaftTensionerWater pumpTiming beltTiming marks keep crankshaft and camshaft in step
How the crankshaft and camshaft run together
How it works ›

What the camshaft position sensor measures

The sensor reads a wheel on the camshaft. On the Saab 9-4X V6 that wheel has 4 teeth of different widths. That gives 4 pulses per camshaft revolution. The engine computer uses the pattern to recognise the position.

The sensor on the intake camshaft at cylinder 1 is the most important one. With it, the computer keeps injection and ignition in step with the engine.

When the computer sets the code

The Saab sets P0340 if the starter motor turns for more than 4 seconds without a pulse. Also if the first revolution after the engine starts gives no pulse. Or if, with the engine running, the pulse is missing in 800 of 1,000 engine cycles.

A signal that drops out now and then sometimes sets no code. The engine can still stall. That is why the manual has you check all the connectors of this sensor.

In numbers

Sensor wheel (Saab 9-4X V6)
4 teeth, 4 pulses per revolution1
Sensor supply
5 V from the engine computer1
Limit when starting
No pulse for more than 4 s1
Limit with the engine running
No pulse in 800 of 1,000 engine cycles1
Computer response
Variable valve timing in rest position, longer starting time1
Engine warning light on
On the second drive in a row with the same fault4

Questions

Can I keep driving with P0340?

A calm drive to the garage is usually fine. Some cars will not start again after switching off without a camshaft signal. So avoid unnecessary stops.

What does a new camshaft position sensor cost?

Around €89 at the garage. On most engines the sensor is easy to reach on the cylinder head.

Can I replace the camshaft position sensor myself?

Often, yes. Usually it is one bolt and a connector. Get the right sensor, because bank 1 and bank 2 can differ.

Can a bad battery cause P0340?

Yes. If the voltage drops too far when starting, the computer can miss the sensor signal. It then stores this code.

See also

Show 3 more ›

Was this helpful?

· 4 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0340, P0345, P0365 or P0390 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
  3. HELLA Tech World, Camshaft sensor: function, fault symptoms and troubleshooting
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.