Skip to content

P0341: Camshaft position sensor A range or performance (bank 1)

Camshaft position sensor A gives a signal that does not match the crankshaft. Usually it is the sensor itself, sometimes a stretched chain or a belt that has jumped a tooth.

This weekYou can drive calmly to the garage, this week. If you hear rattling or the engine runs badly, stop.

How bad
This week
Do it yourself
No, that is a garage job
Usually
Faulty or dirty camshaft position sensor
Garage
usually €89

What you notice

  • Long cranking before it starts
  • Hesitation or misfire
  • Less power
  • Rattling on a cold start
  • Limp mode

What usually causes it

CauseLikelihood
Faulty or dirty camshaft position sensor · €89Common
Stretched timing chain · €712Sometimes
Timing belt that has jumped a tooth or is worn · €725Sometimes
Interference on the cable, for example from a spark plug lead right next to itSometimes
Damaged sensor wheel on the camshaftRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Is P0016 or P0017 stored as well? Then it points more strongly to the timing.
  2. 2Do a cold start. Do you hear rattling from the timing side?
  3. 3Check the connector and the cable of the camshaft position sensor.
  4. 4If the signal and timing are otherwise fine, have the sensor replaced.
  5. 5Have the garage check the timing against the timing marks. Or have the camshaft position measured with a tester.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

A signal that drops out now and then can make the engine stall, without a code. So also check the connectors. Are P0016 or P0017 stored too, and does the engine rattle on a cold start? Then have the timing checked.

  1. First drive with the fault

    The computer stores the fault. It starts using the crankshaft position sensor.

  2. Second drive in a row

    The engine warning light comes on. The engine sometimes takes longer to start.

  3. Signal drops out while driving

    The engine can stall.

  4. With rattling or P0016 as well

    Have the timing measured before you drive any further.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Camshaft position sensorGarage €89Part €24
Timing chainGarage €712Part €100
Timing beltGarage €725Part €49

Background

CamshaftsCrankshaftTensionerWater pumpTiming beltTiming marks keep crankshaft and camshaft in step
How the crankshaft and camshaft run together
How it works ›

How the camshaft position sensor works

The sensor reads the teeth of a wheel on the camshaft. On the Saab 9-4X V6 that wheel has 4 teeth of different widths. The sensor gets 5 V from the engine computer and returns 4 pulses per revolution. From that pattern, the computer works out the position of the camshaft.

The computer uses this to time the injection and the ignition. It also uses it to control the variable valve timing (VVT).

When the computer sets P0341

On the Saab 9-4X V6 with an automatic gearbox, the computer expects exactly 4 pulses in the first engine revolution. While driving it must see 398 to 402 pulses per 100 engine cycles, in 800 of 1,000 cycles. If that is not right, P0341 follows.

When the code is set, the computer puts the variable valve timing in its rest position. For the ignition it then relies on the crankshaft position sensor. The engine can take longer to start.

In numbers

Sensor supply
5 V reference from the engine computer1
Sensor wheel (Saab 9-4X V6)
4 teeth, 4 pulses per revolution1
Expected number of pulses
398 to 402 per 100 engine cycles1
With an active code
Variable valve timing in rest position, longer starting time1
Engine warning light on
On the second drive in a row with the same fault2
Audible sign of a worn chain
Rattling straight after a cold start3

Questions

Is P0341 a sign of a stretched timing chain?

Sometimes, especially if P0016 or P0017 is stored as well and you hear rattling on a cold start. Have it checked soon in that case.

Can I keep driving with P0341?

Driving calmly is fine if the engine runs normally. If you hear rattling or it runs badly, stop. A belt or chain that jumps teeth can damage the valves.

What is the difference between P0340 and P0341?

With P0340 no usable signal comes in. With P0341 a signal does come in, but it does not match the position of the crankshaft.

What does fixing P0341 cost?

Around €89 for a new sensor. A timing belt costs €379 to €899, a chain €479 to €1,000.

See also

Was this helpful?

· 3 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0341, P0346, P0366 or P0391 (factory manual)
  2. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  3. ANWB, Which is better: timing belt or timing chain? (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.