Skip to content

P0100: Mass airflow sensor A: circuit fault

The circuit of your mass airflow sensor (MAF) reports a fault. Often it is a loose connector or a faulty sensor.

Within a monthYou can keep driving, although the car may pull poorly. Have it fixed within a month.

How bad
Within a month
Do it yourself
Yes, you can do it yourself
Garage
Depends on the cause

What you notice

  • The engine warning light or EPC light is on
  • Less power
  • Rough idle
  • Higher fuel consumption

What usually causes it

CauseLikelihood
Loose or corroded connector on the sensorCommon
Faulty mass airflow sensorCommon
Damaged wiringSometimes
Blown fuse for the sensor supplyRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check that the connector on the sensor is firmly attached and dry.
  2. 2Check the wires between the sensor and the engine computer.
  3. 3Have the supply voltage and the signal of the sensor measured.
  4. 4If there is no signal, or it is wrong, fit a new sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

If the sensor does not work properly, the ratio of air to fuel is wrong, according to the ANWB. The engine warning light can then come on.

The service life varies. The ANWB mentions 50,000 km for one car and 250,000 km for another.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Weeks of driving on

    The ratio of air to fuel is not ideal.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, your car fails the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Mass airflow sensorGarage nonePart €72

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

What the mass airflow sensor does

The mass airflow sensor sits in the intake duct and measures how much air the engine draws in. It works with a heated film. Air flowing past cools that film. The electronics turn that into a signal. The engine computer uses it to decide how much fuel to inject.

On a Saab, that signal is a frequency. In the 9-4X V6 it runs from about 2,000 Hz at idle to about 10,000 Hz at full load.

When the computer sets the code

P0100 is the general code for the circuit. In the Saab 9-4X 2.8 turbo, the computer sets it when the signal is 0.0 Hz, so nothing is coming in. A signal that is too low gives P0102 there, a signal that is too high gives P0103.

The manual has you trace the cable. It must not run right next to ignition coils, relays or electric motors. Dirt or water on the sensing element also causes faults.

In numbers

Normal signal (Saab 9-4X V6)
2,000 to 10,000 Hz1
P0100 limit (Saab 9-4X 2.8 turbo)
Signal of 0.0 Hz2
Test runs
Continuously, above 10 V battery voltage2
Signal wire supply
5 V from the engine computer1
Mass airflow sensor replacement (ANWB)
€100 to €250 at a garage3
Engine warning light on
On the second drive in a row with the same fault4

Questions

Can I replace the mass airflow sensor myself?

On most cars, yes. It sits in the air duct after the air filter, with a connector and two clips or screws.

What does a new mass airflow sensor cost?

The part costs €60 to €84. At a garage, replacement costs €100 to €250, according to the ANWB (the Dutch motoring club).

Will P0100 make my car fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. You only fail if they are too high. The rules for each fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0102 or P0103 (factory manual)
  2. Saab WIS, 9-4X 2011 2.8 turbo: DTC P0100 to P0103 (factory manual)
  3. ANWB, What does a mass airflow sensor do? (in Dutch)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.