Skip to content

P0102: Mass airflow sensor A: signal too low

Your mass airflow sensor (MAF) gives a signal that is too low, lower than is possible. Usually it is a loose connector or a faulty sensor.

Within a monthYou can keep driving, gently. Have it fixed within a month.

How bad
Within a month
Do it yourself
Yes, you can do it yourself
Garage
Depends on the cause

What you notice

  • The engine warning light is on
  • Less power
  • Hard starting
  • Stalls at idle

What usually causes it

CauseLikelihood
Loose or corroded connectorCommon
Faulty mass airflow sensorCommon
Broken wire or poor earthSometimes
Large air leak before the sensorRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check that the connector on the sensor is firmly attached.
  2. 2Check the pins for corrosion. If pins are loose, fit a new connector.
  3. 3Have the supply, earth and signal of the sensor measured.
  4. 4If the wires are fine, fit a new sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

Without a usable signal, the computer works with a substitute value. The mixture is then less accurate. According to the ANWB (the Dutch motoring club), the engine warning light can come on.

How long a mass airflow sensor lasts varies widely: according to the ANWB, sometimes 50,000 km, sometimes 250,000 km.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Weeks of driving on

    The ratio of air to fuel is not ideal.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, your car fails the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Mass airflow sensorGarage nonePart €72

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

What the mass airflow sensor does

The mass airflow sensor in the intake duct uses a heated film to measure how much air the engine draws in. The more air flows past, the more the film cools. The electronics turn that into a signal. The engine computer uses it to decide how much fuel to inject.

On a Saab, that signal is a frequency. In the 9-4X V6 it runs from about 2,000 Hz at idle to about 10,000 Hz at full load.

When the computer sets the code

In the Saab 9-4X V6, the computer sets P0102 when the signal stays below 500 Hz for more than 10 seconds. On the 2.8 turbo the limit is 1,135 Hz.

The mass airflow sensor has a supply wire, an earth wire and a signal wire. A break in any of them gives a signal that is too low. The manual also mentions dirt or water on the sensing element.

In numbers

Normal signal (Saab 9-4X V6)
2,000 to 10,000 Hz1
P0102 limit (Saab 9-4X V6)
Below 500 Hz, for more than 10 s1
P0102 limit (Saab 9-4X 2.8 turbo)
Below 1,135 Hz2
Test runs
Engine running for more than 1 s, voltage above 8 V1
Mass airflow sensor replacement (ANWB)
€100 to €250 at a garage3
Engine warning light on
On the second drive in a row with the same fault4

Questions

What is the difference between P0102 and P0103?

With P0102 the signal is too low, with P0103 it is too high. Both usually point to the connector, the wires or the sensor.

Can I keep driving with P0102 for a long time?

A few weeks usually works. The engine then runs on a calculated value. It often uses more fuel.

Will P0102 make my car fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. You only fail if they are too high. The rules for each fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0102 or P0103 (factory manual)
  2. Saab WIS, 9-4X 2011 2.8 turbo: DTC P0100 to P0103 (factory manual)
  3. ANWB, What does a mass airflow sensor do? (in Dutch)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.