- How bad
- This week
- Do it yourself
- Possible, if you are handy
- Usually
- Faulty crankshaft position sensor or camshaft position sensor
- Garage
- usually €89
What you notice
- The engine warning light is on
- The engine stalls while driving
- Hesitation or judders
- The rev counter sometimes drops out
What usually causes it
| Cause | Likelihood |
|---|---|
| Faulty crankshaft position sensor or camshaft position sensor · €89 | Common |
| Loose or corroded connector | Common |
| Metal debris on the sensor | Sometimes |
| Damaged sensor wheel | Rare |
| Poor engine earth connection | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Read all the codes. Look out for P0335 or P0340 alongside it.
- 2Check that the connector on the crankshaft position sensor is firmly in place.
- 3Remove the sensor. Wipe the metal debris off the tip.
- 4Check the earth cable between the engine and the body.
- 5Replace the crankshaft position sensor. The part costs €25 to €29.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What does an original part cost, and what does a pattern part cost?
- What will it cost if you find more? Call me before you go ahead.
If you wait
HELLA lists stalling and poor starting as consequences. A signal that drops out now and then can later fail completely.
Code appears
The engine can stall.
Signal drops out completely
The engine no longer starts.
What it costs
It depends on the cause. Where do the prices come from? ›
| Part | At the garage | Part only |
|---|---|---|
| Crankshaft position sensor | Garage €89 | Part €27 |
| Camshaft position sensor | Garage €89 | Part €24 |
Background
How it works ›
Where the engine speed signal comes from
The crankshaft position sensor reads a toothed wheel on the crankshaft. On the Saab 9-4X V6 that wheel has 58 teeth with a gap of two teeth. Each revolution gives 58 pulses. The engine computer uses the gap to recognise the position of the crankshaft.
The computer uses the signal to time the ignition and injection. The rev counter also runs on it.
When the computer sets the code
The Saab 9-5 diesel sets its code for an incorrect crankshaft signal when starting and with the engine running. On that car the engine warning light comes on straight away.
The manual lists damage to the sensor or toothed wheel, play or a loose sensor, incorrect fitting and too large an air gap between the sensor and the toothed wheel. HELLA also mentions metal filings on the sensor.
In numbers
Questions
What is the difference between P0321 and P0322?
With P0321 a signal comes in that is wrong. With P0322 nothing comes in, and then the engine often will not start.
Can a crankshaft position sensor fail when the engine is warm?
Yes, that happens often. Your car then stalls when warm. It only starts again after it cools down.
Will P0321 make me fail the APK (the Dutch MOT)?
No, not on the code itself. Because of the P code, the APK inspector measures the exhaust gases. If they are too high, you fail the APK.
See also
Was this helpful?
· 5 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-4X 2011 V6: DTC P0335 (factory manual)
- Saab WIS, 9-5 2011 diesel: DTC P0336 (factory manual)
- Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
- HELLA Tech World, Crankshaft sensor: function and troubleshooting
- Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.