- How bad
- Stop
- Do it yourself
- Possible, if you are handy
- Usually
- Faulty crankshaft position sensor
- Garage
- usually €89
What you notice
- The engine turns over but will not start
- The engine stalls while driving
- The rev counter stays at zero when starting
- The engine warning light is on
What usually causes it
| Cause | Likelihood |
|---|---|
| Faulty crankshaft position sensor · €89 | Common |
| Loose or broken connector | Common |
| Broken cable | Sometimes |
| The fuse for the sensor supply has blown | Sometimes |
| Faulty engine computer | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Watch the rev counter while starting. If it stays at zero, the code is correct.
- 2Check that the connector on the crankshaft position sensor is firmly in place and undamaged.
- 3Check the engine management fuses.
- 4Have the sensor supply and signal measured.
- 5If the wiring is fine, fit a new crankshaft position sensor.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What does an original part cost, and what does a pattern part cost?
- What will it cost if you find more? Call me before you go ahead.
If you wait
Without an engine speed signal, the computer does not know when to ignite and inject. HELLA lists stalling and not starting as consequences.
Code appears
The engine stalls or will not start.
Engine starts again
The fault can come back. Have the sensor and wiring measured.
What it costs
It depends on the cause. Where do the prices come from? ›
| Part | At the garage | Part only |
|---|---|---|
| Crankshaft position sensor | Garage €89 | Part €27 |
Background
How it works ›
Where the engine speed signal comes from
The crankshaft position sensor reads a toothed wheel on the crankshaft. On the Saab 9-4X V6 that wheel has 58 teeth with a gap of two teeth. Each revolution gives 58 pulses. The engine computer uses the gap to recognise the position of the crankshaft.
The computer uses the signal to time the ignition and injection. The rev counter also runs on it.
When the computer sets the code
The Saab 9-4X V6 sets its code for a missing crankshaft signal if the starter motor turns for more than 4 seconds without a pulse. With the engine running, the code follows if the pulse is missing in 2 of 10 revolutions.
HELLA lists a broken cable, a short circuit, a damaged toothed wheel and metal filings on the sensor as causes.
In numbers
Questions
Can I still drive with P0322?
Preferably not. The engine can stall on the road and then not start again.
What does a new crankshaft position sensor cost?
The part costs €25 to €29. A garage charges about €89 to replace it.
Does the car need to be towed?
Yes, if the engine will not start. If the sensor fails when it is warm, you can sometimes still get to the garage after it cools down.
See also
Was this helpful?
· 5 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-4X 2011 V6: DTC P0335 (factory manual)
- Saab WIS, 9-5 2011 diesel: DTC P0336 (factory manual)
- Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
- HELLA Tech World, Crankshaft sensor: function and troubleshooting
- Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.