- How bad
- Within a month
- Do it yourself
- Possible, if you are handy
- Garage
- Depends on the cause
What you notice
- The engine warning light is on
- Less power
- Higher fuel use
What usually causes it
| Cause | Likelihood |
|---|---|
| Loose or corroded connector on the knock sensor | Common |
| Damaged or chafed cable | Common |
| Faulty knock sensor | Sometimes |
| Real engine knock or mechanical noise | Rare |
| Faulty engine computer | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Read all the codes. Look out for P0325 or P0327 alongside it.
- 2Check that the knock sensor connector is firmly in place and dry.
- 3Follow the wiring. Look for chafed spots, or oil in the connector.
- 4Have the sensor and the wiring tested.
- 5Replace the knock sensor. If it sits under the intake manifold, it is more work.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What will it cost if you find more? Call me before you go ahead.
If you wait
With a fault in the circuit, the Saab retards the ignition to protect the engine. HELLA lists less power and higher fuel use as the result.
The manual lists a dropped or damaged sensor, a bolt that is too loose or too tight, and dirt on the mounting surface. The sensor must be clear of hoses, brackets and cables.
Code appears
The computer retards the ignition.
Weeks of driving on
You have less power. The car uses more fuel.
At the APK
The APK inspector sees the P code and measures the exhaust gases.
Background
How it works ›
What the knock sensor does
The knock sensor is a piezo element on the engine block. It turns engine vibrations into an alternating voltage. The engine computer learns what noise level is normal. On top of that, it recognises the pinking of an early combustion.
If the computer hears pinking, it retards the ignition. After that it keeps trying to return to the normal timing.
When the computer sets the code
The Saab 9-4X V6 sets the code if the signal wires of the sensor on bank 1 are shorted to positive for more than 10 seconds.
The 2.8 turbo looks at the level. If the signal stays above the highest noise level the engine normally makes for more than 1 second, P0328 follows.
In numbers
- Signal
- Alternating voltage from a piezo element3
- P0328 limit (Saab 9-4X V6)
- Short to positive, for more than 10 s1
- P0328 limit (Saab 9-4X 2.8 turbo)
- Above the maximum noise level, for more than 1 s2
- Computer response
- Ignition retarded1
- Voltage at unplugged connector (Saab 9-4X 2.8 turbo)
- 2.30 to 2.80 V to earth2
Questions
What does a knock sensor do?
It hears pinking in the engine. The computer then retards the ignition, to prevent damage.
Why does the car have less power with P0328?
Without a reliable knock signal, the computer retards the ignition to be safe. That costs power and fuel.
Will P0328 make me fail the APK (the Dutch MOT)?
Not on the code itself. Because of the P code, the APK inspector does measure the exhaust gases. Emissions that are too high mean you fail the APK.
See also
Was this helpful?
· 6 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-4X 2011 V6: DTC P0324 to P0333, P06B6 or P06B7 (factory manual)
- Saab WIS, 9-4X 2011 2.8 turbo: DTC P0326 to P0333 (factory manual)
- Saab WIS, 9-4X 2011 V6: Electronic Ignition System Description (factory manual)
- HELLA Tech World, Check knock sensor: function, fault symptoms and testing
- Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
- RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)