Skip to content

P0010: Variable valve timing A: circuit fault (bank 1)

The valve that adjusts your camshaft is not getting a proper current signal, on bank 1. Usually the solenoid valve itself or a poor connector.

Within a monthYou can keep driving, take it easy. Have it checked within a month.

How bad
Within a month
Do it yourself
Possible, if you are handy
Garage
Depends on the cause

What you notice

  • The engine warning light is on
  • Rough idle
  • Less pulling power at low revs
  • Higher fuel consumption

What usually causes it

CauseLikelihood
Faulty VVT solenoid valveCommon
Loose or corroded connector on the valveCommon
Damaged or chafed wiringSometimes
Faulty engine computerRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Read all codes. Check whether P0011 or P0012 is there too.
  2. 2Is the connector on the valve secure? Also look for green deposits on the pins.
  3. 3Follow the wires to the engine computer. Look for chafed spots or melted insulation.
  4. 4Measure the resistance of the valve. Compare it with the factory value.
  5. 5If it differs, or the valve does not switch, fit a new valve.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

With a fault in the adjustment, the Saab also returns the camshaft on the other bank to its rest position. The engine then runs without adjustment.

The factory manual gives more power, lower fuel consumption and lower emissions as the purpose of the adjustment. That is lost while the valve is not working.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Weeks of driving on

    The camshaft stays in the rest position. You lose some torque and economy.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, the car fails the APK.

Background

CamshaftsCrankshaftTensionerWater pumpTiming beltTiming marks keep crankshaft and camshaft in step
How the crankshaft and camshaft run together
How it works ›

What the solenoid valve does

The engine computer adjusts the camshafts while the engine is running. Each camshaft has an actuator that works on oil pressure. A solenoid valve sends the oil to the actuator. The actuator turns the camshaft earlier or later relative to the crankshaft.

The computer controls the valve with a pulsed 12 V signal. P0010 is about the valve for the intake camshaft on bank 1.

When the computer sets the code

On the Saab 9-4X V6, the computer compares what it tells the valve to do with what it sees back on the control wire. If they do not match for longer than 5 seconds, it sets P0010. The test runs continuously while the computer is controlling the valve.

It is an electrical test of the valve, connector and wiring. The camshaft position is P0011. Chain or belt is P0016.

In numbers

Solenoid valve signal
12 V, pulse width1
Code limit (Saab 9-4X V6)
Command and circuit differ for longer than 5 s1
Battery voltage during test
11 to 32 V1
With a fault
Actuators return to the rest position2
Engine warning light on
On the second drive in a row with the same fault3
Engine warning light goes off
After 3 drives in a row without the fault4

Questions

What is the difference between P0010 and P0011?

P0010 is about the current to the solenoid valve. With P0011, the camshaft itself does not reach the right position.

What does a VVT solenoid valve cost?

That varies by engine. Garages charge €75 to €103 per hour.

Will P0010 fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the usual way. Only if they are too high does the car fail the APK. The rules for each fuel type are in the APK guide. This fault can increase emissions.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0010, P0013, P0020 or P0023 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: Camshaft Actuator System Description (factory manual)
  3. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  4. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  5. RDW, APK handbook regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)