- How bad
- Stop
- Do it yourself
- No, that is a garage job
- Garage
- €175 to €350
What you notice
- Smell of fuel around the engine
- Engine stalls and will not restart
- Car in limp mode
- Wet patches under the car
What usually causes it
| Cause | Likelihood |
|---|---|
| Leaking line or coupling | Common |
| Empty tank, or air in the system | Sometimes |
| Injector with too much return leakage | Sometimes |
| High-pressure pump leaking or faulty · €263 | Sometimes |
| Faulty rail pressure sensor | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Switch off the engine. Look under the bonnet and under the car for fuel.
- 2If you smell fuel, have the car towed.
- 3If you see and smell nothing, check that your tank is not nearly empty.
- 4Have the garage pressure test the lines and check the injectors for leak-off.
- 5If no leak is found, have the rail pressure sensor and the high-pressure pump tested.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What will it cost if you find more? Call me before you go ahead.
If you wait
With this code, the Mazda limits engine torque and stops EGR control and diesel particulate filter (DPF) regeneration. The engine warning light comes on during the first drive.
The pressure in a common rail system on the Saab 9-5 diesel rises to 1,600 bar.
Code appears
The engine warning light comes on and torque may be limited.
Fuel visible or smelt
Switch off the engine. Do not drive on.
No leak found
The fuel is escaping inside the system. The garage checks the pressure relief valve, control valve, sensor, injectors and pump.
What it costs
It depends on the cause. Where do the prices come from? ›
Background
How it works ›
How the computer detects a leak
The engine computer knows the pressure in the rail and how much fuel it injects. If more fuel disappears from the high-pressure section than that explains, it assumes a leak.
That can be fuel running out. It can also be fuel escaping inside the system, for example past a pressure relief valve or an injector.
When the computer sets the code
In the workshop manual for the Mazda SKYACTIV-D 2.2, the computer sets P0093 when it calculates a leak quantity above 480 mm3 per revolution three times. The test runs above 600 rpm.
Mazda lists as causes the pressure relief valve, the suction control valve on the pump, the rail pressure sensor, an injector, a leaking or loose line and the pump itself.
In numbers
- Limit (Mazda SKYACTIV-D 2.2)
- Leak above 480 mm3 per revolution, measured 3 times1
- Test runs
- Above 600 rpm, battery voltage 8 V or more1
- Engine warning light on (Mazda)
- On the first drive1
- Computer response (Mazda)
- Torque limited, EGR and DPF regeneration stopped1
- Common rail pressure (Saab 9-5 diesel)
- Up to 1,600 bar2
Questions
Can I keep driving with P0093?
No, not until you are sure nothing is leaking. A leak on the high-pressure side sprays fuel onto hot parts.
Can an empty tank cause P0093?
Yes, on some diesels. The pressure then drops suddenly. The computer sees that as a leak.
Will a fuel leak make my car fail the APK (the Dutch MOT)?
Yes, a leaking fuel system fails the APK. The code itself is not the reason.
See also
Was this helpful?
· 2 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.