Skip to content

P0190: Fuel rail pressure sensor circuit fault

The engine computer is not getting a good signal from the pressure sensor on the fuel rail. Usually it is a loose connector or a faulty sensor.

This weekYou can drive gently to the garage. Go this week, because the engine can stall on the way.

How bad
This week
Do it yourself
No, that is a garage job
Garage
€175 to €350

What you notice

  • Limp mode, with little power
  • Long cranking, or no start at all
  • Stalling while driving
  • Stumbles when you accelerate

What usually causes it

CauseLikelihood
Loose or corroded connector on the sensorCommon
Faulty rail pressure sensorCommon
Cable to the engine computer chafed throughSometimes
Sensor not sold separately, so the rail has to come outRare
Fault in the engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check that the connector on the sensor is firmly in place. It should be dry and clean.
  2. 2Check the cable to the sensor for cracks, chafing and oil or diesel.
  3. 3Have the sensor supply measured. It should be around 5 volts.
  4. 4In the app, compare the measured rail pressure with the requested pressure. If the value is stuck or cannot be right, it is the sensor.
  5. 5Have the garage replace the sensor. Do not do this yourself, the system is under very high pressure.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

Without a reliable pressure signal, the computer cannot control the pump properly. Expect less power until the fault is fixed.

  1. First drive with the fault

    On the Saab 9-4X V6, the engine warning light comes on straight away.

  2. While driving

    The car may limit power.

  3. At the APK (the Dutch MOT)

    With a P-code, the APK inspector measures the exhaust gases. If the car is registered with a diesel particulate filter (DPF), the inspector always measures with a particle counter.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Fuel pumpGarage €263Part none
InjectorsGarage nonePart €117

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

What the rail pressure sensor does

The sensor sits on the fuel rail and measures the pressure to the injectors. You find it mainly on common rail diesels and petrol engines with direct injection. It gets 5 V from the engine computer. High pressure gives a high signal voltage, low pressure a low one.

The computer controls the high-pressure pump based on this signal. In the Saab 9-5 diesel, the pressure rises to 1,600 bar.

When the computer sets the code

P0190 is the general code for the circuit. The Saab 9-5 diesel splits the fault out: below 0.254 V for half a second is P0192, above 4.7 V is P0193.

On the Saab 9-4X V6 these are type A codes. The engine warning light comes on straight away and the car may report that power is limited.

In numbers

Sensor supply
5 V from the engine computer1
Too low (Saab 9-5 diesel)
Below 0.254 V, 0.5 s2
Too high (Saab 9-5 diesel)
Above 4.7 V, 0.5 s2
Common rail pressure (Saab 9-5 diesel)
Up to 1,600 bar3
Engine warning light on (Saab 9-4X V6)
Straight away, at the first failed test4
Engine warning light goes off
After 3 drives in a row without the fault5

Questions

What does the rail pressure sensor do?

It measures the fuel pressure in the rail to the injectors. The engine computer uses it to control the high-pressure pump and the injection.

Can I keep driving with P0190?

Only briefly and gently to the garage. The engine can go into limp mode or stall. After that it sometimes will not start again.

Can I replace the rail pressure sensor myself?

Better not. It is under hundreds to over 1,000 bar of pressure. The sensor also has to be tightened to the correct torque.

What does replacing the rail pressure sensor cost?

That differs per engine. If the sensor is not sold separately, the whole rail has to come out and it costs more. Garages charge an hourly rate of €75 to €103.

See also

Was this helpful?

· 7 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0192 or P0193 (factory manual)
  2. Saab WIS, 9-5 2011 diesel: DTC P0192 or P0193 (factory manual)
  3. Saab WIS, 9-5 2011 diesel: Fuel System Description (factory manual)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  6. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
  7. RDW, APK Keurmeester No. 110 (September 2025): when is a soot measurement required? (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.