Skip to content

P0191: Fuel rail pressure sensor range or performance

The rail pressure sensor gives a value that does not match what the engine computer expects. Usually it is the sensor itself or a clogged fuel filter.

This weekYou can drive gently to the garage. Go this week, because the engine can go into limp mode or stall.

How bad
This week
Do it yourself
No, that is a garage job
Garage
€175 to €350

What you notice

  • Limp mode
  • Stumbles or hesitates when pulling away
  • Long cranking
  • Stalling
  • You use more fuel

What usually causes it

CauseLikelihood
Sensor gives wrong valuesCommon
Clogged fuel filter, especially on dieselsCommon
Faulty pressure control valve or volume control valveSometimes
Air in the system, after a filter change or running the tank drySometimes
Worn high-pressure pump · €263Rare
Leaking injector, returns too much fuelRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1If you recently ran the tank dry or just had the filter replaced, there may be air in the system.
  2. 2If the fuel filter is past its interval, replace it.
  3. 3While driving, compare the measured and requested rail pressure in the app. If the measured pressure lags behind, it is a pressure problem.
  4. 4Ignition on, engine off. The rail pressure should then be around 0 bar. If it shows more, the sensor is suspect.
  5. 5Have the pressure control valve measured. Also have the injector return flow measured.
  6. 6Only when the sensor, filter and control valve are fine, fit a new high-pressure pump.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

According to the manual, a fault in the pump in the tank or its control module can also give this code.

  1. First start with the fault

    On the Saab 9-4X V6, the engine warning light comes on straight away.

  2. While driving

    The car may limit power.

  3. At the APK (the Dutch MOT)

    With a P-code, the APK inspector measures the exhaust gases. If the car is registered with a diesel particulate filter (DPF), the inspector always measures with a particle counter.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Fuel pumpGarage €263Part none
InjectorsGarage nonePart €117

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

What the rail pressure sensor does

The sensor sits on the fuel rail and measures the pressure to the injectors. It gets 5 V from the engine computer. High pressure gives a high signal voltage, low pressure a low one.

When the computer sets the code

P0191 is a logic check. The Saab 9-4X V6 does it at start-up, after the car has stood still for at least 4.2 hours. The pressure in the rail has then dropped, so the sensor should give a low value.

If the sensor reads more than 15 bar with the ignition on and there is also a code for pressure that is too high, the signal is wrong. The same applies to less than 1.2 bar with a code for pressure that is too low.

In numbers

Sensor supply
5 V from the engine computer1
Standstill before the test (Saab 9-4X V6)
At least 4.2 hours1
Too high with ignition on
Above 15 bar, with a code for pressure that is too high1
Too low with ignition on
Below 1.2 bar, with a code for pressure that is too low1
Engine warning light on (Saab 9-4X V6)
Straight away, at the first failed test2
Engine warning light goes off
After 3 drives in a row without the fault3

Questions

What is the difference between P0190 and P0191?

P0190 is an electrical fault in the circuit. With P0191 there is a signal, but the value does not fit the situation.

Can I keep driving with P0191?

Only gently to the garage. With the wrong rail pressure, the engine can lose power or cut out on the way.

Can a fuel filter cause P0191?

Yes, especially on diesels. A clogged filter allows too little fuel through. Then the rail pressure lags behind.

What does a new high-pressure pump cost?

Garages charge €175 to €1,470 for a new fuel pump. Have the cheaper causes ruled out first.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0191 (factory manual)
  2. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  3. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  4. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
  5. RDW, APK Keurmeester No. 110 (September 2025): when is a soot measurement required? (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.