Skip to content

P0118: Coolant temperature sensor 1 signal too high

Your engine computer thinks your engine is ice cold, because the sensor signal is too high. Usually a loose connector or a broken wire.

Within a monthYou can keep driving, gently. Have it fixed within a month.

How bad
Within a month
Do it yourself
Possible, if you are handy
Garage
Depends on the cause

What you notice

  • The engine warning light is on
  • The radiator fan keeps running
  • The temperature gauge stays low
  • Higher fuel consumption

What usually causes it

CauseLikelihood
Loose or corroded connectorCommon
Faulty coolant sensorCommon
Broken wireSometimes
Faulty engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check that the connector on the sensor is firmly in place.
  2. 2Look at the coolant temperature in the app. If it shows around -40 °C, the circuit is open.
  3. 3Check the wires to the sensor for breaks.
  4. 4Replace the sensor and bleed the cooling system.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

With this code too, the Saab can switch the radiator fans to their highest speed, until the code has been cleared.

HELLA often sees a higher idle speed, poor starting and higher fuel consumption with this fault.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Radiator fans keep running

    That is the computer’s response to the code.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

Background

RadiatorExpansion tankThermostatWater pumpEngineHotCooled
How the engine cooling works
How it works ›

How the temperature sensor works

The temperature sensor is a resistor in the coolant, with 5 V from the engine computer on the signal wire. The colder the engine, the higher the resistance. The voltage rises with it.

HELLA gives a guide value of 2.0 to 6 kOhm at 25 °C and about 300 ohm at 80 °C.

When the computer sets P0118

The computer reads a high voltage as an ice-cold engine. The Saab 9-4X V6 sets P0118 if it reads less than -39 °C for longer than 1 second, or for 10 seconds added together. The test already runs with the ignition on.

HELLA names an open circuit in the wiring as the cause. A loose connector gives the same picture.

In numbers

Sensor supply
5 V from the engine computer1
P0118 limit (Saab 9-4X V6)
Below -39 °C, for longer than 1 s1
Resistance at 25 °C
2.0 to 6 kOhm2
Wiring continuity
About 0 ohm2
After a night parked
Within 3 °C of the intake air sensor1
Engine warning light on
On the second drive in a row with the same fault3

Questions

Why do I use more fuel with P0118?

The computer thinks the engine is cold. It then injects extra fuel, as it does on a cold start.

What does fixing P0118 cost?

Securing a loose connector costs nothing. A new sensor is the part plus labour. Garages charge €75 to €103 per hour.

Will P0118 make you fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the normal way. You only fail the APK if they are too high. The rules per fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 4 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0117 or P0118 (factory manual)
  2. HELLA Tech World, Checking the coolant temperature sensor
  3. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  4. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)