Skip to content

P0134: Lambda sensor no activity detected (bank 1, sensor 1)

Your first lambda sensor (oxygen sensor) on bank 1 gives no usable signal. Usually a faulty sensor or a heater that does not work.

Within a monthYou can keep driving. Have it fixed within a month, that saves fuel and spares the catalytic converter.

How bad
Within a month
Do it yourself
Possible, if you are handy
Usually
Faulty lambda sensor
Garage
usually €116

What you notice

  • The engine warning light is on
  • Higher fuel consumption
  • Rough running with a cold engine

What usually causes it

CauseLikelihood
Faulty lambda sensor · €116Common
Faulty heater in the sensor · €116Sometimes
Broken wire or loose connectorSometimes
Exhaust leak before the sensorRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1If P0135 is also stored, the heater is probably the cause.
  2. 2Check the connector and wires of the sensor.
  3. 3Look at the sensor signal in the app, with a warm engine.
  4. 4If the signal does not move, fit a new lambda sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

Without a usable signal from sensor 1, the computer cannot control the mixture on the sensor. The manual names a mixture that is too lean or too rich as a cause of damage to the catalytic converter.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Months of driving on

    The computer does not control the mixture on the sensor. That puts strain on the catalytic converter.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

What the front lambda sensor does

A lambda sensor produces a voltage from the difference in oxygen between the exhaust gas and the outside air. That voltage lies between 0 and 1,275 mV: around 1,000 mV the mixture is rich, close to 0 mV lean.

After the start, the engine computer ignores the sensor. Only when the voltage moves back and forth enough does it switch to controlling with the sensor.

When the computer sets the code

With P0134 the signal does not start moving. The Saab 9-4X V6 sets the code if the voltage of sensor 1 stays stuck between 350 and 550 mV while the sensor heater has done its job. Within 15 seconds the code is set.

The test starts when the engine has been running for 150 seconds. If there is also a code for the sensor heater, such as P0135, fix that first.

In numbers

Sensor signal range
0 to 1,275 mV1
P0134 limit (Saab 9-4X V6)
Signal stays between 350 and 550 mV1
Code set within
15 s1
Test starts
After 150 s of engine running1
Engine warning light on
On the second drive in a row with the same fault3
Engine warning light goes off
After 3 drives in a row without the fault4

Questions

What is the difference between P0133 and P0134?

With P0133 the sensor responds too slowly. With P0134 it gives no usable signal at all.

What does a new lambda sensor cost?

The part costs €57 to €100. Replacing it at the garage costs €112 to €120.

Will P0134 make you fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the normal way. You only fail the APK if they are too high. The rules per fuel type are in the APK guide. This fault can raise emissions.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0134, P0140, P0154 or P0160 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: DTC P0420 or P0430 (factory manual)
  3. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  4. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  5. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.