Skip to content

P0130: Lambda sensor circuit fault (bank 1, sensor 1)

The signal from your first lambda sensor (oxygen sensor) on bank 1, before the catalytic converter, is not right. Usually a worn sensor or damaged wires.

Within a monthYou can keep driving. Have it fixed within a month, that spares your catalytic converter.

How bad
Within a month
Do it yourself
Possible, if you are handy
Usually
Worn or faulty lambda sensor
Garage
usually €116

What you notice

  • The engine warning light is on
  • Higher fuel consumption
  • Uneven idle
  • Emissions too high

What usually causes it

CauseLikelihood
Worn or faulty lambda sensor · €116Common
Damaged wires or connectorSometimes
Exhaust leak before the sensorSometimes
Engine running too rich or too lean because of another faultSometimes
Faulty engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1If there are other codes, such as P0171 or P0300, fix those first.
  2. 2Check the connector and wires of the sensor. They run close to hot exhaust parts.
  3. 3Do a cold start. If you hear ticking or blowing at the exhaust manifold, your exhaust is leaking.
  4. 4Look at the sensor signal in the app. With a warm engine it should move up and down quickly.
  5. 5Replace the lambda sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Weeks of driving on

    The computer controls the mixture less precisely. That puts strain on the catalytic converter.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79
Catalytic converterGarage €339Part €240

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

What the front lambda sensor does

The lambda sensor before the catalytic converter measures whether the mixture is rich or lean. The engine computer puts a voltage of about 450 mV on the signal. With a rich mixture the sensor rises to about 1,000 mV, with a lean mixture it drops to about 10 mV.

For a good sensor, Bosch gives a signal that swings between about 0.1 and 0.9 V, 0.3 to 3 times per second.

When the computer sets P0130

In the factory manual of the Saab 9-4X V6, the computer sets P0130 if the front sensor reports something different from the rear sensor. That is the case if the front sensor reports rich, above 600 mV, while the rear one stays below 100 mV.

With the ignition on and the engine off, the signal should be between 350 and 550 mV. If it is higher, there is a fault in the wiring. The manual names moisture in the connector as a cause.

What the sensor itself tells you

Bosch links the colour of the deposits to a cause. Green and grainy points to coolant in the combustion, black and oily to oil consumption, dark brown to a mixture that is too rich. Fix the cause as well, or the new sensor will fail just as quickly.

In numbers

Reference voltage from the computer
About 450 mV1
Signal range
About 10 mV (lean) to 1,000 mV (rich)1
Ignition on, engine off
350 to 550 mV1
Good sensor according to Bosch
0.1 to 0.9 V, 0.3 to 3 Hz2
Lean or rich
Below 0.4 V lean, above 0.5 V rich2
Engine warning light on
On the second drive in a row with the same fault4

Questions

What does bank 1, sensor 1 mean?

Sensor 1 is the sensor before the catalytic converter. Bank 1 is the side of the engine with cylinder 1. An inline four-cylinder engine only has bank 1.

Can I replace a lambda sensor myself?

With a sensor socket and penetrating oil it often works. A seized sensor is difficult, though. The garage charges €112 to €120.

Will P0130 make you fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the normal way. You only fail the APK if they are too high. The rules per fuel type are in the APK guide.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0130 (factory manual)
  2. Bosch, Checking the signal of lambda sensors (workshop sheet) (in Dutch)
  3. Bosch, How do you recognise a faulty lambda sensor? (workshop sheet) (in Dutch)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. Saab WIS, 9-4X 2011 V6: DTC P0420 or P0430 (factory manual)
  6. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.