Skip to content

P0135: Lambda sensor heater circuit fault (bank 1, sensor 1)

The heater of your first lambda sensor (oxygen sensor) on bank 1 is not working properly. Usually it has burnt out. A new sensor at the garage costs €112 to €120.

No rushYou can keep driving. Fix it within a few months.

How bad
No rush
Do it yourself
Possible, if you are handy
Usually
Heater in the sensor burnt out

What you notice

  • The engine warning light is on
  • Slightly higher fuel consumption on short trips

What usually causes it

CauseLikelihood
Heater in the sensor burnt out · €116Common
Sensor heater fuse blownSometimes
Damaged wires or connectorSometimes
Faulty relay or engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check the lambda sensor fuse in the fuse box.
  2. 2Check that the sensor connector is firmly in place and not melted.
  3. 3Measure the resistance of the heater. If there is no continuity, the sensor is faulty.
  4. 4Replace the lambda sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

Without the heater, it takes longer after a cold start before the engine computer can control the mixture on the sensor.

The engine warning light stays on. Bosch calls lambda sensors wear parts that you should have checked regularly.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Months of driving on

    After a cold start, the computer starts controlling the mixture on the sensor later.

  4. At the APK

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

Why a lambda sensor has a heater

A lambda sensor compares the oxygen content in the exhaust gases with the outside air. That only works when the sensor is hot. A heating element in the sensor brings it up to temperature quickly after a cold start.

Sensor 1 sits before the catalytic converter and controls the mixture.

When the computer sets the code

In the factory manual of the Saab 9-4X V6, the normal heater current is 0.2 to 1.5 amps. The computer sets P0135 if the current is above 3.1 or below 0.3 amps for longer than 8 seconds. The test runs once per drive, when the sensor has been at temperature for 120 seconds.

Bosch measures the supply first: there should be a constant 10.5 to 13.5 V. Then comes the resistance of the element, which should be below 30 ohm when cold, at 20 °C. Shortly after the start the element gets no current yet, until the dew point in the exhaust has passed.

In numbers

Normal heater current (Saab 9-4X V6)
0.2 to 1.5 A1
Limit for the code
Above 3.1 A or below 0.3 A, for longer than 8 s1
Test runs
1 time per drive, after 120 s with the sensor at temperature1
Heater supply
Constant 10.5 to 13.5 V2
Element resistance at 20 °C
Below 30 ohm2
Engine warning light on
On the second drive in a row with the same fault4
Engine warning light goes off
After 3 drives in a row without the fault5

Questions

Why does a lambda sensor have a heater?

The sensor only works properly when it is hot. The heater makes it work soon after a cold start.

Can a fuse cause P0135?

Yes. Check it first, that is the cheapest.

Will P0135 make you fail the APK (the Dutch MOT)?

Not on the code alone. With a P code, the APK inspector measures the exhaust gases in the normal way. You only fail the APK if they are too high. The rules per fuel type are in the APK guide.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0030 to P0161, lambda sensor heater (factory manual)
  2. Bosch, Checking the heating element of lambda sensors (workshop sheet) (in Dutch)
  3. Bosch, How do you recognise a faulty lambda sensor? (workshop sheet) (in Dutch)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  6. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.