Skip to content

P0141: Lambda sensor heater circuit fault (bank 1, sensor 2)

The heater of your second lambda sensor (oxygen sensor) on bank 1, after the catalytic converter, is not working properly. Usually the sensor itself has failed.

No rushYou can keep driving. Fix it when it suits you.

How bad
No rush
Do it yourself
Possible, if you are handy
Usually
Heater in the sensor burnt out

What you notice

  • The engine warning light is on
  • Usually you notice nothing

What usually causes it

CauseLikelihood
Heater in the sensor burnt out · €116Common
Blown fuseSometimes
Damaged wiring under the carSometimes
Faulty relay or engine computerRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check the fuse for the lambda sensor.
  2. 2Look under the car to see if the connector and wiring of the second sensor are intact.
  3. 3Measure the resistance of the heater.
  4. 4Replace the lambda sensor after the catalytic converter.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

Without the heater, the computer is less able to test the catalytic converter.

According to Bosch, a lambda sensor wears and should be checked regularly.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Months of driving on

    The catalytic converter test works less well.

  4. At the APK (the Dutch MOT)

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

Why a lambda sensor has a heater

A lambda sensor measures the difference in oxygen between exhaust gas and outside air. It can only do that when it is hot. The heating element brings it up to temperature quickly after a cold start.

Sensor 2 sits behind the catalytic converter and checks whether the converter works. Bosch writes that the computer only switches on the heater of a sensor far from the engine after some driving.

When the computer sets the code

In the factory manual of the Saab 9-4X V6, the normal heater current is 0.2 to 1.5 amps. The computer sets P0141 if the current is above 2.9 or below 0.3 amps for more than 8 seconds. The test runs once per trip, when the sensor has been at temperature for 120 seconds.

Bosch measures the supply first: there should be a constant 10.5 to 13.5 V. Next comes the resistance of the element, which should be under 30 ohms when cold, at 20 °C. Shortly after the start, the element gets no current yet, until the exhaust is past its dew point.

In numbers

Normal heater current (Saab 9-4X V6)
0.2 to 1.5 A1
Threshold for the code
Above 2.9 A or below 0.3 A, for more than 8 s1
Test runs
1 test per trip, after 120 s with the sensor at temperature1
Heater supply
Constant 10.5 to 13.5 V2
Element resistance at 20 °C
Under 30 ohms2
Engine warning light on
On the second drive in a row with the same fault4
Engine warning light goes off
After 3 drives in a row without the fault5

Questions

Do I need to fix P0141 straight away?

No, you notice little of it while driving. Do plan it in. The engine warning light stays on.

What does fixing P0141 cost?

A fuse costs little. A new lambda sensor at the garage costs €112 to €120.

Will P0141 fail the APK (the Dutch MOT)?

Not on the code alone. With a P-code, the APK inspector measures the exhaust gases in the normal way. You only fail if they are too high. The rules for each fuel type are in the APK guide.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0030 to P0161, lambda sensor heater (factory manual)
  2. Bosch, Checking the heating element of lambda sensors (workshop sheet) (in Dutch)
  3. Bosch, How do you recognise a faulty lambda sensor? (workshop sheet) (in Dutch)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  6. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.