Skip to content

P0136: Lambda sensor circuit fault (bank 1, sensor 2)

The signal from your second lambda sensor (oxygen sensor), after the catalytic converter on bank 1, is not right. Usually it is the sensor itself or the wiring.

No rushYou can keep driving. Fix it within a few months.

How bad
No rush
Do it yourself
Possible, if you are handy
Usually
Faulty lambda sensor after the catalytic converter

What you notice

  • The engine warning light is on
  • Usually you notice nothing

What usually causes it

CauseLikelihood
Faulty lambda sensor after the catalytic converter · €116Common
Damaged wiring or connectorSometimes
Exhaust leak near the sensorSometimes
Faulty catalytic converter · €339Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Check the connector and wiring of the second sensor, under the car.
  2. 2See if the exhaust is leaking around the sensor.
  3. 3Look at the signal in the app. After a warm drive it should be fairly stable.
  4. 4Replace the lambda sensor after the catalytic converter.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

The engine usually keeps running normally, because the mixture is controlled on sensor 1. The catalytic converter test does use sensor 2. Without a good signal, that test is not reliable.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The light comes on.

  3. Months of driving on

    The engine runs normally. The catalytic converter is not monitored properly.

  4. At the APK (the Dutch MOT)

    The APK inspector measures the exhaust gases. If they are too high, you fail the APK.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79
Catalytic converterGarage €339Part €240

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

What the rear lambda sensor does

The rear sensor also turns the difference in oxygen between exhaust gas and outside air into a voltage of 0 to 1,275 mV. The closer to 1,000 mV, the richer the mixture. The closer to 0 mV, the leaner.

Sensor 2 sits behind the catalytic converter. With this sensor, the engine computer measures how much oxygen the catalytic converter can store. The Saab 9-4X V6 also trims the mixture slightly to keep the voltage of this sensor between 580 and 665 mV.

When the computer sets the code

P0136 is the general code for this sensor’s circuit. The Saab 9-4X V6 splits the fault out. Below 50 mV it is P0137, above 1,050 mV it is P0138. If the voltage does not move at all, it is P0140.

The computer decides within 50 seconds. The tank must be more than 10 per cent full.

In numbers

Sensor signal range
0 to 1,275 mV1
Too low (Saab 9-4X V6)
Below 50 mV gives P01371
Too high (Saab 9-4X V6)
Above 1,050 mV gives P01381
Target value after the catalytic converter
580 to 665 mV4
Engine warning light on
On the second drive in a row with the same fault5
Engine warning light goes off
After 3 drives in a row without the fault6

Questions

Is a lambda sensor after the catalytic converter important?

Not much for how the engine runs. The computer uses it to monitor the catalytic converter.

Can P0136 lead to P0420 later?

Yes. A bad second sensor can disturb the catalytic converter test.

Will P0136 fail the APK (the Dutch MOT)?

Not on the code alone. With a P-code, the APK inspector measures the exhaust gases in the normal way. You only fail if they are too high. The rules for each fuel type are in the APK guide.

See also

Was this helpful?

· 7 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0131, P0132, P0137, P0138 and related codes (factory manual)
  2. Saab WIS, 9-4X 2011 V6: DTC P0134, P0140, P0154 or P0160 (factory manual)
  3. Saab WIS, 9-4X 2011 V6: DTC P0420 or P0430 (factory manual)
  4. Saab WIS, 9-4X 2011 V6: DTC P2096 (factory manual)
  5. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  6. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  7. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.