- How bad
- This week
- Do it yourself
- No, that is a garage job
- Garage
- €89 to €225
What you notice
- The engine warning light is on
- Limp mode or less power
- The car sometimes does not start, or stalls
- The accelerator pedal responds oddly
What usually causes it
| Cause | Likelihood |
|---|---|
| Internal fault in the engine computer | Common |
| Low battery voltage or voltage spikes · €118 | Sometimes |
| Software that needs an update | Sometimes |
| Moisture or corrosion in the engine computer | Sometimes |
| Poor earth connection | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Have the battery tested. Check the earth cables.
- 2Clear the code and see if it comes back. A one-off voltage dip can give a stray report.
- 3Ask the garage or dealer about a software update.
- 4Check that the engine computer is dry. Is there corrosion on the connector?
- 5Have the engine computer reconditioned or replaced. Afterwards it must be programmed again.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What will it cost if you find more? Call me before you go ahead.
If you wait
Reprogramming needs special equipment and the right software for the car.
The ANWB (the Dutch motoring club) expects an engine computer to last at least 6 years. How the car is used has little effect on that.
Code appears
Check the battery, terminals and earth first.
Code returns
Have the supply and earth of the engine computer measured.
Supply in order
The computer then needs to be reprogrammed or replaced.
At the APK
With a P-code, the APK (the Dutch MOT) inspector measures the exhaust gases in the standard way.
What it costs
It depends on the cause. Where do the prices come from? ›
| Part | At the garage | Part only |
|---|---|---|
| Battery | Garage €118 | Part none |
Background

How it works ›
What the engine computer checks in itself
The engine computer tests its own processor and memory. On Saab, the test for P0606 runs continuously as soon as the voltage is above 6 V. The code follows if the computer finds an internal fault, or if the software is missing or loaded incorrectly.
Where to start
The factory manual starts with the power supply. A low voltage or a brief interruption of the positive or earth can set this code. Check that the battery is fully charged. Also check that the battery terminals are clean and tight.
Then check the earth cables and supply wires of the engine computer for open circuits, short circuits and resistance. Only when that is correct does the computer itself come into the picture.
In numbers
Questions
Can I keep driving with P0606?
Sometimes you notice nothing. The engine can suddenly go into limp mode or stall, though. So drive as little as possible.
Can a used engine computer be fitted?
Often only if it is adapted to your car, because of the immobiliser. That is work for a specialist.
What is the difference between P0600 and P0606?
P0600 is about communication. P0606 is about the processor in the computer itself.
See also
Was this helpful?
· 4 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
- Saab WIS, 9-4X 2011 V6: DTC P0601 to P0606, P062B, P062F, P0630, P16F3 or P2610 (factory manual)
- Saab WIS, 9-4X 2011 V6: Engine Control Module Description (factory manual)
- ANWB, What to do when the EPC light is on? (in Dutch)
- RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.