- How bad
- Within a month
- Do it yourself
- Possible, if you are handyWith a lambda sensor socket and penetrating oil you can often swap it yourself. Let the exhaust cool down first. If the sensor has rusted in, go to the garage. Otherwise you’ll damage the thread in the exhaust.
Prices
Including 21% VAT, 19 November 2026. Where do they come from? ›
Garage, with labour
Middle of 2, €112 to €120.
- Vandaag Auto's19 Nov€112
- Carpardoo magazine19 Nov€120
Part only
Middle of 2, €57 to €100.
Without fitting. A garage often replaces more parts with it.
- mijnautoonderdelen categorie19 Nov€57
- autoonderdelen24 categorie19 Nov€100
What it does
The lambda sensor measures how much oxygen is in your exhaust gas. The engine computer uses that to adjust the mix of air and fuel. There’s one before the catalytic converter. Usually there’s also one after it, which checks that the catalytic converter works.
How you notice
- Engine warning light is on
- You use more fuel
- Rough idle
- Rotten egg smell from the exhaust
- Code for the sensor heater, such as P0135 or P0141
When to replace it
There’s no fixed interval. Check your service book.
If you wait
With a bad sensor the engine computer can’t control the mix properly. You use more fuel. The engine can idle roughly or stall.
Over time a bad sensor can damage the catalytic converter. A sensor is much cheaper than a catalytic converter.
Light comes on
The engine warning light is on. Have the code read and the live values measured before you buy a sensor.
After weeks
The mix is less accurate. You use more fuel and the engine can run rough.
At the APK
A lambda value outside 0.97 to 1.03 or a stored P code: then you fail.
If you keep driving
Your catalytic converter can get damaged.
Background
How it works ›
What the lambda sensor does
The engine burns cleanest at 14.7 kg of air to 1 kg of fuel. That’s called lambda 1.
The lambda sensor measures the oxygen in the exhaust gases. The engine computer uses that to adjust the mix. Without a good signal the catalytic converter can’t do its job.
How a sensor wears
A lambda sensor is a wear part. It ages over time.
Fuel additives, silicones and carbon deposits can make a sensor fail sooner. Dirty fuel and oil residue burning along with the fuel also shorten its life a lot.
Bosch advises having the sensors checked every 30,000 km. If the sensor has aged, have it replaced.
Measure first, then replace
A fault code about the lambda sensor or the mixture doesn’t always mean the sensor is broken. An air leak, the wrong fuel pressure or a blocked injector can give the same code.
Have the garage measure the live values and the exhaust gases. Also look at plugs and wiring. Tighten a new sensor to the right torque: 35 to 45 Nm for an 18 mm sensor.
In numbers
- Ideal mixture
- 14.7 kg of air to 1 kg of fuel (lambda 1)3
- Check interval
- Have it checked every 30,000 km (Bosch advice)1
- Replacement
- No fixed interval, replace when it has aged1
- Torque
- 35 to 45 Nm (18 mm), 18 to 23 Nm (12 mm)3
- APK lambda value, petrol
- Between 0.97 and 1.03 at raised engine speed5
- APK OBD test
- No stored fault code starting with a P5
- Causes of early failure
- Fuel additives, silicones and carbon deposits3
Questions
What happens if you don’t replace a broken lambda sensor?
You use more fuel. Over time your catalytic converter gets too much unburnt fuel.
Does a broken lambda sensor fail the APK?
It can. Petrol cars from after 1995 must have a working catalytic converter and lambda sensor. At raised engine speed the lambda value must be between 0.97 and 1.03. In the OBD test there must be no stored fault code starting with a P.
Is a P0420 always the catalytic converter?
No. A slow sensor after the catalytic converter can give the same code. Get the sensors checked first. They’re much cheaper.
See also
Was this helpful?
· 5 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.