Skip to content

P0105: MAP sensor or barometric pressure sensor: circuit fault

The MAP sensor, which measures the pressure in your intake, gives a wrong signal. Usually it is a loose hose or a bad connector.

Within a monthYou can keep driving. Have it looked at within a month.

How bad
Within a month
Do it yourself
Possible, if you are handy
Garage
Depends on the cause

What you notice

  • The engine warning light is on
  • Rough idle
  • Higher fuel consumption
  • Hesitates when pulling away

What usually causes it

CauseLikelihood
Loose, cracked or blocked hose to the sensorCommon
Loose or corroded connector on the MAP sensorCommon
Faulty MAP sensorSometimes
Damaged wiringSometimes
Faulty engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Read all the codes. P0106, P0107 or P0108 tells you what is wrong.
  2. 2Check that the vacuum hose to the sensor is secure and intact.
  3. 3Unplug the connector. If you see green corrosion, clean it and push it firmly back on.
  4. 4Have the sensor compared with the outside air pressure with the ignition on.
  5. 5If the value is wrong, fit a new MAP sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

In the Saab 9-4X V6, the MAP sensor shares its 5 V supply with accelerator pedal sensor 2. A short circuit in one takes the other down with it.

A MAP sensor that reads off also makes the calculated outside air pressure wrong.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The engine warning light comes on.

  3. Weeks of driving on

    The computer works with a wrong intake pressure.

  4. At the APK

    The APK inspector measures the exhaust gases, because a P code is stored.

Background

Air filterMass airflow sensorThrottleInjectorIntake manifoldTo exhaustPistonFuel tankFuel pump
How the air and fuel mixture is made
How it works ›

How the intake pressure sensor is connected

The MAP sensor measures the pressure in the intake manifold. It has three wires: a 5 V supply, earth and a signal wire. The voltage on the signal wire moves with the pressure.

The engine computer also uses the sensor as a barometer. With the ignition on and the engine off, it reads the outside air pressure with it.

When the computer sets the code

P0105 is the general code for the circuit. The Saab 9-4X V6 splits it up. Below 0.20 V, for more than 5 seconds, it is P0107. Above 4.80 V it is P0108.

If the voltage is fine but the pressure does not match the other readings, it is P0106.

In numbers

Sensor supply
5 V from the engine computer1
Too low (Saab 9-4X V6)
Below 0.20 V, for more than 5 s, gives P01071
Too high (Saab 9-4X V6)
Above 4.80 V, for more than 5 s, gives P01081
Shares 5 V supply with
Accelerator pedal sensor 2 (Saab 9-4X V6)3
Engine warning light on
On the second drive in a row with the same fault4
Engine warning light goes off
After 3 drives in a row without the fault5

Questions

What does a MAP sensor do?

It measures the pressure in the intake. The engine computer uses it to calculate how much air is coming in. That tells it how much fuel to add.

Can I replace a MAP sensor myself?

Often, yes. It is usually held on the intake by 1 or 2 small bolts, with one connector.

Will P0105 make my car fail the APK (the Dutch MOT)?

Only if emissions are too high. Because of the P code, the APK inspector does carry out an exhaust gas test.

See also

Was this helpful?

· 6 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0107 or P0108 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: DTC P0106 (factory manual)
  3. Saab WIS, 9-4X 2011 V6: DTC P0641, P0651, P0697 or P06A3 (factory manual)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. UNECE Regulation No. 83, Annex 11 (OBD), paragraphs 3.3 to 3.8
  6. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)