- How bad
- Within a month
- Do it yourself
- Possible, if you are handy
- Usually
- Faulty camshaft position sensor
- Garage
- usually €89
What you notice
- The engine warning light is on
- Longer cranking before it starts
- Hesitation or less power
- Sometimes stalls
What usually causes it
| Cause | Likelihood |
|---|---|
| Faulty camshaft position sensor · €89 | Common |
| Loose or corroded connector | Common |
| Broken cable or short to earth | Sometimes |
| Weak battery or low system voltage · €118 | Sometimes |
| Faulty engine computer | Rare |
A code points to the area. Sometimes the garage only finds the real cause after that.
How to fix it
Start with what costs least.
- 1Read all the codes. Look out for P0340 or P0335 alongside it.
- 2Have the battery tested. Low voltage when starting can cause this code.
- 3Check that the connector on the camshaft position sensor is firmly in place and dry.
- 4Have the sensor supply and signal measured.
- 5If the wiring is fine, fit a new sensor. The part costs €23 to €25.
What to ask the garage
- Which other codes are stored, and can I have the printout?
- Which measurement shows that this is the cause?
- What does an original part cost, and what does a pattern part cost?
- What will it cost if you find more? Call me before you go ahead.
If you wait
A signal that drops out now and then can make the engine stall. HELLA lists starting problems, a lit engine warning light and an emergency program as consequences.
Code appears
The engine can take longer to start.
Signal drops out while driving
The engine can stall.
At the APK
Because a P code is stored, the APK inspector carries out an exhaust gas test.
What it costs
It depends on the cause. Where do the prices come from? ›
| Part | At the garage | Part only |
|---|---|---|
| Camshaft position sensor | Garage €89 | Part €24 |
| Battery | Garage €118 | Part none |
Background
How it works ›
How the camshaft position sensor works
The sensor is a Hall switch. It reads a wheel with 4 teeth on the camshaft. It gets 5 V and earth from the engine computer. It returns a square wave, alternating high and low.
Sensor A on bank 1 is the sensor on the intake camshaft at cylinder 1. With it, the computer keeps injection and ignition in step with the engine.
When the computer sets the code
The Saab 9-4X 2.8 turbo sets the code if the signal voltage stays low. The computer then sees no pulses for more than 1 second, or for 10 seconds added together.
The test runs after 10 crankshaft revolutions, below 2,520 rpm. The manual also lists damage, play, too large an air gap and dirt between the sensor and the wheel.
In numbers
Questions
What is the difference between P0342 and P0343?
P0342 is a signal that is too low, often a short to earth. P0343 is too high, often a broken wire.
Can I replace a camshaft position sensor myself?
Often, yes. It is usually held by one bolt on top of or on the side of the cylinder head.
Will P0342 make me fail the APK (the Dutch MOT)?
Only if emissions are too high. Because of the P code, the APK inspector carries out a standard exhaust gas test.
See also
- P0340: Camshaft position sensor A circuit fault (bank 1)
- P0341: Camshaft position sensor A range or performance (bank 1)
- P0343: Camshaft position sensor A: signal too high (bank 1)
- P0335: Crankshaft position sensor A circuit fault
- P0016: Crankshaft and camshaft out of sync
- Camshaft position sensor
- Battery
- Engine warning light
Was this helpful?
· 3 sources · In het Nederlands
Sources
All sources checked on 19 November 2026.
How we set prices ›
The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.