Skip to content

P0715: Gearbox input speed sensor fault

Your computer is not measuring the speed at the input of the automatic gearbox properly. Usually it is the sensor itself, metal particles or the wiring.

This weekDrive gently and as little as possible. Have it checked this week. The gearbox can drop into limp mode.

How bad
This week
Do it yourself
No, that is a garage job
Garage
Depends on the cause

What you notice

  • Harsh or late gear changes
  • The gearbox stays stuck in one gear
  • The speedometer may behave oddly
  • The gearbox warning light or engine warning light is on

What usually causes it

CauseLikelihood
Faulty input speed sensorCommon
Metal particles on the sensorSometimes
Wiring or connector damagedSometimes
Problem in the gearbox computerRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Also read the gearbox computer. Are there more codes?
  2. 2Have the sensor connector checked for oil and corrosion.
  3. 3Have the sensor signal measured during a test drive.
  4. 4Replace the sensor. On some gearboxes it sits in the valve body. Then it is more work.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

On a Saab the engine warning light comes on immediately. The gearbox sets the fluid pressure to maximum, disengages the torque converter and limits itself to fifth gear and reverse.

According to the ANWB (the Dutch motoring club), a gearbox overhaul costs about 2,500 euros, including fitting.

  1. Code appears

    The engine warning light comes on. The gearbox goes into limp mode.

  2. Driving on

    You only have fifth gear and reverse. Drive gently to a garage.

  3. At the APK

    With a P code, the APK (the Dutch MOT) inspector measures the exhaust gases the normal way.

Background

EngineClutchFlywheelClutch platePressure plateGearboxInput shaftOutput shaftDifferentialDriveshaftWheel
How power reaches the wheels
How it works ›

What the input speed sensor measures

The sensor measures how fast the input side of the automatic gearbox turns. In the Saab 9-4X it is a Hall sensor in the gearbox housing, aimed at a toothed ring on a clutch housing. It gets 8.3 to 9.3 V from the gearbox computer.

The computer uses the signal for the fluid pressure, the shift points, the torque converter slip and the gear ratio.

When the computer sets the code

P0715 is the general code for this circuit. Saab splits it out. If the speed drops by 1,350 rpm within 1 second without recovering, it is P0716. If it stays below 50 rpm for 5 seconds while the car is going faster than 16 km/h, it is P0717.

A damaged or misaligned toothed ring also causes a sensor fault.

In numbers

Sensor supply (Saab 9-4X automatic)
8.3 to 9.3 V1
Threshold P0716
Speed drops 1,350 rpm in 1 s without recovery1
Threshold P0717
Below 50 rpm, 5 s, above 16 km/h1
Gearbox response
Maximum fluid pressure, fifth gear and reverse only1
Gearbox overhaul (ANWB)
About €2,500, including fitting2

Questions

Can I keep driving with P0715?

Briefly and gently, yes. Harsh gear changes put strain on the gearbox and can cause damage.

Is my gearbox broken?

Usually not. Often only the sensor or the cable is faulty.

What is gearbox limp mode?

The gearbox stays in one fixed gear to protect itself. You can still drive, slowly.

See also

Was this helpful?

· 3 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 automatic 6T70: DTC P0716 or P0717 (factory manual)
  2. ANWB, Gearbox (in Dutch)
  3. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)