Skip to content

P0730: Incorrect gear ratio

The input and output speeds of your automatic gearbox do not match the gear. Sometimes old fluid or too little fluid, sometimes wear in the gearbox.

This weekDrive as little as possible. Have it checked this week.

How bad
This week
Do it yourself
No, that is a garage job
Garage
Depends on the cause

What you notice

  • The engine slips, or revs up without accelerating
  • Harsh or late gear changes
  • The gearbox warning light or engine warning light is on
  • Limp mode

What usually causes it

CauseLikelihood
Too little or worn transmission fluidCommon
Faulty shift valve in the valve bodySometimes
Speed sensor gives a wrong signalSometimes
Worn clutch plates in the gearboxSometimes
Faulty torque converterRare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Have the gearbox fluid level checked.
  2. 2Read the gearbox computer. Are there codes for sensors or valves?
  3. 3If the fluid is old, dark or smells burnt, have it changed.
  4. 4Have an automatic gearbox specialist test the valve body.
  5. 5If there is internal wear, the gearbox needs an overhaul.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

With a fault in a speed sensor, the Saab limits the gearbox to fifth gear and reverse.

A gearbox wears because the gears mesh with each other, writes the ANWB (the Dutch motoring club). According to the ANWB, a gearbox overhaul costs about 2,500 euros, including fitting.

  1. Code appears

    Have the gearbox codes read. Also have the fluid level checked.

  2. Gearbox slips or shifts harshly

    Drive as little as possible. Slipping wears the gearbox.

  3. At the APK

    With a P code, the APK (the Dutch MOT) inspector measures the exhaust gases the normal way.

Background

EngineClutchFlywheelClutch platePressure plateGearboxInput shaftOutput shaftDifferentialDriveshaftWheel
How power reaches the wheels
How it works ›

How the gearbox checks its ratio

An automatic gearbox has one speed sensor on the input side and one on the output side. The gearbox computer divides one speed by the other. The result should match the gear it has selected.

In the Saab 9-4X these are Hall sensors that get 8.3 to 9.3 V. The computer also uses them for the fluid pressure and the torque converter slip.

What the code means

P0730 means the measured ratio does not match the selected gear. That can be slip in the gearbox. It can also be a speed sensor that measures incorrectly.

If there is also a code for one of the speed sensors, such as P0715, solve that first.

In numbers

Speed sensor supply (Saab 9-4X automatic)
8.3 to 9.3 V1
Use of the signals
Fluid pressure, shift points, slip and gear ratio2
Limp mode with a sensor fault (Saab 9-4X automatic)
Fifth gear and reverse only1
Gearbox overhaul (ANWB)
About €2,500, including fitting3

Questions

Is P0730 the end of my gearbox?

Not always. Start with the fluid and the sensors. Those are cheaper and are also common causes.

What does a gearbox overhaul cost?

About €2,500, including fitting, according to the ANWB (the Dutch motoring club). A used gearbox is sometimes cheaper.

Can I keep driving with a slipping gearbox?

Better not. Slipping quickly makes the plates and the fluid worse.

See also

Was this helpful?

· 4 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 automatic 6T70: DTC P0716 or P0717 (factory manual)
  2. Saab WIS, 9-4X 2011 automatic 6T70: DTC P0722 or P0723 (factory manual)
  3. ANWB, Gearbox (in Dutch)
  4. RDW, APK manual Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)