Skip to content

P0140: Lambda sensor after the catalytic converter gives no signal (bank 1, sensor 2)

The lambda sensor (oxygen sensor) behind your catalytic converter, on bank 1, is not giving a usable signal. Usually it is a worn sensor. Replacing it costs €112 to €120.

No rushYou can keep driving, there is no hurry. Have it fixed before the next APK (the Dutch MOT).

How bad
No rush
Do it yourself
Possible, if you are handy
Usually
Worn lambda sensor after the catalytic converter

What you notice

  • The engine warning light is on
  • Often you notice nothing while driving

What usually causes it

CauseLikelihood
Worn lambda sensor after the catalytic converter · €116Common
Loose or corroded connectorCommon
Burnt or damaged cable near the exhaustSometimes
Exhaust leak just before the sensorSometimes
Faulty engine computer (ECU)Rare

A code points to the area. Sometimes the garage only finds the real cause after that.

How to fix it

Start with what costs least.

  1. 1Read all the codes. If P0141 is there too, the heater of this sensor has also failed.
  2. 2Check that the connector of the rear sensor is firmly in place.
  3. 3Look for melted spots on the cable where it runs along the exhaust.
  4. 4Have the voltage checked with a warm engine. It should switch between about 0.1 and 0.9 volts.
  5. 5If the signal stays still, fit a new sensor.

What to ask the garage

  • Which other codes are stored, and can I have the printout?
  • Which measurement shows that this is the cause?
  • What does an original part cost, and what does a pattern part cost?
  • What will it cost if you find more? Call me before you go ahead.

If you wait

The mixture is controlled on sensor 1. The catalytic converter test does use sensor 2. Without a good signal, that test is not reliable.

  1. First drive with the fault

    The computer stores the fault.

  2. Second drive in a row

    The engine warning light comes on.

  3. Months of driving on

    The engine runs normally. The catalytic converter is not monitored properly.

  4. At the APK

    The APK inspector measures the exhaust gases, because there is a P-code.

What it costs

It depends on the cause. Where do the prices come from? ›

PartAt the garagePart only
Lambda sensorGarage €116Part €79
Catalytic converterGarage €339Part €240

Background

Engine managementLambda sensorbefore converterLambda sensorafter converterCatalytic converterEngineControls the mixtureChecks the converter
How the lambda sensors measure
How it works ›

What the rear lambda sensor does

The lambda sensor compares the oxygen in your exhaust gas with the outside air. It turns that into a voltage. The voltage runs from 0 to 1,275 mV.

Sensor 2 sits behind the catalytic converter. With this sensor, the engine computer measures how much oxygen the catalytic converter can store. The Saab 9-4X V6 keeps the voltage of this sensor between 580 and 665 mV.

When the computer sets the code

The Saab 9-4X V6 sets the code if the voltage of sensor 2 stays still while the sensor heater has finished warming up. The code is set within 15 seconds.

The test starts once the engine has been running for 150 seconds. If there is also a code for this sensor’s heater, such as P0141, fix that first.

In numbers

Sensor signal range
0 to 1,275 mV1
P0140 threshold (Saab 9-4X V6)
Voltage of sensor 2 does not change1
Code set within
15 s1
Test starts
After 150 s of engine running1
Target value after the catalytic converter
580 to 665 mV3
Engine warning light on
On the second drive in a row with the same fault4

Questions

Is P0140 serious?

Usually not. The rear sensor only checks your catalytic converter. The engine keeps running normally.

Which sensor is bank 1, sensor 2?

The sensor behind the catalytic converter, on the side of cylinder 1. A 4-cylinder engine has only one bank.

Will P0140 fail the APK (the Dutch MOT)?

Not for the code alone. Because of the P-code, the APK inspector does an exhaust gas test. You only fail if the emissions are too high.

See also

Was this helpful?

· 5 sources · In het Nederlands

Sources

All sources checked on 19 November 2026.

  1. Saab WIS, 9-4X 2011 V6: DTC P0134, P0140, P0154 or P0160 (factory manual)
  2. Saab WIS, 9-4X 2011 V6: DTC P0420 or P0430 (factory manual)
  3. Saab WIS, 9-4X 2011 V6: DTC P2096 (factory manual)
  4. Saab WIS, 9-4X 2011: Powertrain DTC Type Definitions (factory manual)
  5. RDW, APK handbook Regulations, articles 42 and 45a to 45g (version from 1 January 2024) (in Dutch)
How we set prices ›

The amounts come from prices that Dutch garages and webshops publish on their own sites, including VAT, or from the source shown next to them. Last collected on 19 November 2026. Your own price depends on your engine and year, so always ask for a quote. The ANWB (the Dutch motoring club) gives an average, which is not a real price, so we leave it out. If your garage asks something very different, email it to hallo@vroomdoctor.com.